Chris Miller

My rhthym guitar sound is based on the use of a 1995 Matchless Tube Pre-amp (original Hot Box before the labeling) running dual mono into a Marshall Valvestate VS232 and to a Peavey Decade, which isn't specifically depicted on the board schematics. 

To avoid any potential impedance issues with the Matchless Tube Preamp, I use a Vertex Interface buffer to assist my pedal chain as follows: running from the guitar to the Send input, from the Send out I go to the Matchless and then back into the Guitar Input of the Vertex. Then from the Guitar output (using a Vertex Y-cable), we go to both a Sonic Research Tuner ST-300 (in true bypass, on all all the time, no output use) and the split goes to a Stone Deaf PDF-1. 

I use a Lehle mono volume pedal after my gain stages to roll up or down the overall volume while maintaining the selected gain outputs (capabilities from the Matchless Preamp, a Stone Deaf PDF-1 and an MXR Fat Sugar).  From the PDF-1 we follow a basic right of passage, going from its non-expressive output to the Fat Sugar input, then out to a Subdecay custom Envelope Filter, then to the input of a GE-7 EQ (with XTS Mod).  

From the GE-7, we go to the Lehle mono volume, then on to a JHS Kill Switch input (because I love having a panic button).  From the Kill Switch we go out to a Thorpy’s CamoFlange with dual outs.  Here, using a Lehle Little Dual amp switcher to split my mono signals to one or both amps through the Vertex, we go from one flanger output to the AB input of the Little Dual and the other output of the flanger to the input of a Foxgear EchoSex Baby. The EchoSex runs out to the A input of the Little Dual. The Little Dual then feeds the two separate amplifier input channels on the Vertex interface from its respective A & B outputs, then using both separate outputs from the Vertex Interface Buffer to both my Marshall and Peavey for a mixed blend ultimately controlled by the Little Dual. 

I use a TrueTone 1Spot CS-12 to power everything except the Matchless, which has it's own built-in power cable/requirement.

1970 Les Paul Deluxe Gold Top

Matchless Preamp Rhythm Guitar Station

'65 Twin Reverb

Cameron LeViere

The CAMOFLANGE Flanger MKII is here and more than a visual change we have made some internal changes too. We have adjusted the internal voltage regime to offer higher voltage (18v) and use higher headroom BBDs. Crucially though, all the magic that was the original Camoflange is still present. Designed as a collaboration with DAN COGGINS (Former LOVETONE Pedal designer) as his second modulation pedal design since his Lovetone pedal days. This fully Analog Flanger was designed from the ground up to provide the most incredibly versatile flanger sounds with a level of versatility unsurpassed in analog effects so far.

ThorpyFX

Demo by collector//emitter

Demo by Noise Generator

Product Page

Review by The Gear Page

Review by delicious audio

Review by reddit /guitarpedals

Manual

Camoflange MKII

JakobSlash

Das GE-7 Equalizer-Pedal bietet sieben EQ-Bänder im Bereich von 100Hz bis 6,4kHz, ideal für Gitarrensounds, mit einer Anhebung/Absenkung von +/- 15dB pro Band. Damit kannst du deinen Sound vollständig kontrollieren und unerwünschte Rückkopplungen eliminieren, insbesondere wenn du ihn nach einem Verzerrungseffekt anschließt.

The GE-7 Equalizer pedal offers seven bands of EQ ranging from 100Hz to 6.4kHz, ideal for guitar sounds, with boost/cut of +/- 15dB per band. This lets you completely control your sound and eliminate unwanted feedback, particularly when connected after a distortion effect.

BOSS

Official Website

Review by The Gear Check

Review by Audiofanzine

Review by Reddit /guitarpedals

Review by Guitar Gear

Manual's All

Demo by Law of the Riff

Demo by New Music Academy

Demo by Guitar Bonedo

Demo by Musicmaker

GE-7 Equalizer

QuickMount Type E

Pedal-Montageplatte für Standard-Boss-Pedale

Pedal Mounting Plate For Standard Boss Pedals

Filippo Rimondi

Truetone

Visual Sound 1 Spot Pro CS12

Stone Deaf Effects

Demo by Simon Smith

Demo by Pedal of the Day

Review by Premier Guitar

PDF-1

Tester

Sonic Research

Demo by StrobeTuner

ST-300 Turbo Tuner

Sean Sheppard

Vertex Effects

Buffer Interface

David Litaba

Simpel, solide und nützlich. Der JHS Mute Switch ist genau der einfache Stummschalter den du schon immer gebraucht hast. Tritt drauf und alles, was du daran anschließt ist sofort 100 % still!

Simple, solid and very useful. Have you ever needed a simple mute switch with no frills? Just hit the footswitch and anything plugged into the input is made 100% silent.

Official Product Page

Demo by Pedal Empire

Mute Switch

QuickMount Type L

Pedal-Montageplatte für Standard-Mini-Pedale

Pedal Mounting Plate For Standard Mini Pedals

Das Foxgear Echosex Baby der noch relativ jungen italienischen Marke stellt eine handliche und vor allem geldbeutelschonende Variante einer analogen Echomaschine dar, die Musikgeschichte geschrieben hat, nämlich des Binson Echorecs. Dieses Gerät hatte seinen Ursprung bereits in den 60er Jahren ebenfalls in Italien und ist auf diversen Pink Floyd- und Led Zeppelin-Aufnahmen zu hören. Längst gilt das Original als begehrtes Sammlerobjekt, das horrende Preise auf dem Gebrauchtmarkt erzielt.

FOXGEAR Echosex Baby Delay compact effect pedal is the smaller version of Guru's award-winning Echosex. This is one of the best quality stompboxes you'll find at an entry-level price.
FOXGEAR is an italian company endorsed by some huge names like Steve Lukather (Toto), Adrian Belew (King Crimson) and Phil Campbell (Motorhead)

Foxgear

Review by Guitar Interactive Magazine 

Review by bonedo 

Demo by Guitar Interactive Magazine 

Demo by Guitar Bonedo 

Demo by Pete Thorn 

Echosex Baby

Yamile Butler

Der LEHLE LITTLE DUAL II ist der Nachfolger des Lehle Little Dual und stellt einen Amp-Switcher für zwei Amps mit höchster Signaltreue dar. Mittels Soft-Touch-Schaltern kannst du zwischen zwei angeschlossenen Verstärkern brumm- und soundverlustfrei umschalten.
Dir stehen zwei verschiedene Betriebsmodi bereit. Du entscheidest, ob du jeden Ausgang einzeln aktivieren und deaktivieren willst oder klassisch hin- und herschalten möchtest und den jeweils anderen hinzufügen oder entfernen.

The LEHLE LITTLE DUAL is the LEHLE DUAL SGOS's little sister, a maximum signal-fidelity amp switcher for two amps. Both amps are activated simultaneously using the left footswitch, while the right is used to switch back and forth between them. High-intensity LEDs make it easy to read off switching state A or B, or A and B, even under high-power spots.

LEHLE

Official Product Video

Review by Samuel Roberts, guitar.com 

Little Dual II

The MXR Fat Sugar Drive brings the Sugar Drive’s diverse range of clear and transparent overdrive tones to MXR’s classic housing for players who prefer its footprint over that of the mini.

This pedal’s versatility comes from its unique Drive control—which replicates an amp’s transition from clean to dirty by blending your clean signal at the start of the sweep—and a little something called a voltage doubler, which increases overall headroom and opens up the sound of the pedal. Together, these elements allow you to serve up everything from a sauced-up boost to full-on blow-tube distortion.

The Fat Sugar Drive is set for true bypass by default, but for the tonal purists who want buffered bypass instead, just remove the bottom plate and flick the internal Buffer switch, close it up, and get to playing. This special edition comes with a custom pink sparkle finish.

Review by HOMETONEBLOG

Demo by The Music Addict

Demo by The Pedal Picassos

M94SE Fat Sugar Drive

QuickMount Type A

Pedal-Montageplatte für Standard-Einzelpedale

Pedal Mounting Plate For Standard Single Pedals

The Gurgle and Moan is an envelope filter effect. This is a prototype pedal, and it does have some quirks and rough edges. On a few of them that we have built they oscillate with the resonance knob cranked. Also there is a bit of a "gurgle" in the background due to some crosstalk issues with the control voltage circuitry. I thought it sounded cool, although it may not be what everyone wants in a filter. 

This is a prototype pedal, and has no artwork, or labeling on the face of the pedal. There is a sticker on the back with a brief explanation of what the knobs do.

Controls
Lower right knob: Shape - Varies the shape of the filter from band pass or low pass.
Lower left knob: Resonance - Accents the cut off frequency of the filter. (At max setting it may oscillate)
Upper right knob: Depth- Varies how far your playing dynamics will modulate the filter cutoff frequency.
Upper left knob: Frequency - Varies the cut off frequency of the filter

Warranty: If it ever breaks send it back to us and we will fix it, unfortunately we no longer cover polar bear attacks, alien abduction, willfully destroyed pedals, or any claims involving time travel or toaster repair.

This pedal can be powered by a 9V battery or a standard boss style barrel plug adaptor. Has an LED, True bypass, and a powder coated finish for durability.

Subdecay

Review by Talk Bass.com

Gurgle & Moan

Matchless Pre-amp 2 channel Clean and Gain

Matchless

Demo by PedalSoundMafia

Demo by funk ojisan

Review by Les Paul Forum

Review by guitartest

Schematic

Hot Box

Wenn Burkhard Lehle etwas baut, dann richtig und ohne Kompromisse. Mit seinem Mono Volume Pedal hat er ein High End Pedal ohne die sonst bei Volumenpedalen auftretenden Nachteile konstruiert. Es wird kein mechanisches Poti verwendet - das Mono Volume arbeitet mit einem Magnet Sensor der ein hochwertiges VCA steuert. Dadurch ist der gesammte Regelbereich gleichmäßig und ohne Klangverlust, Verschleiß und Potikratzen gehören der Vergangenheit an. Desweiteren besteht die Möglichkeit, das Ausgangssignal um bis zu 10 dB zu boosten. Das Pedal läuft sehr gleichmäßig und ruhig, da die Pedalwippe in Low Friction Polymer Gleitlagern läuft. Zusätzlich steht ein gebufferter Direkt Out zur Verfügung der als Tuner Out oder zur Weiterleitung an weiteres Equipment genutzt werden kann. Das Pedal läßt sich durch den niederohmigen Ausgang auch in einem seriellen FX Loops eines Amps betreiben.

When Burkhard Lehle builds something, he does it properly and without compromise. With his Mono Volume Pedal, he has constructed a high-end pedal without the disadvantages that usually occur with volume pedals. No mechanical potentiometer is used - the Mono Volume works with a magnetic sensor that controls a high-quality VCA. This means that the entire control range is even and without loss of sound, wear and potentiometer scratching are a thing of the past. There is also the option of boosting the output signal by up to 10 dB. The pedal runs very evenly and quietly because the pedal rocker runs on low friction polymer plain bearings. There is also a buffered direct out that can be used as a tuner out or for forwarding to other equipment. The pedal can also be operated in a serial FX loop of an amp thanks to the low-impedance output.

Demo by shnobel

Review by Michael Behm

Mono Volume

Für 9-18 FX-Pedale, 2 MOD-Slots - **722 x 330 mm / 28.43" x 12.99"** - erhältlich mit Gig Bag oder Flight Case

For 9 - 18 FX pedals, 2 MOD slots - **722 x 330 mm / 28.43" x 12.99"** - available with Gig Bag or Flight Case

Taoufik Bennani

Die überarbeiteten RockBoard® MODs V2 sind einfache all-in-one Patchbays für die RockBoard Pedalboard Series mit einem neuen, überarbeiteten Design und einem kompakten Gehäuse. Passend für alle neuen RockBoards® (außer der DUO-Serie) mit einem MOD-Slot, bieten sie als komfortable Patchbay verschiedene Kabelverbindungen, um eine weite Reihe von Bedürfnissen abzudecken. Mit den RockBoard® MODs kannst du deine Pedale dauerhaft unter dem Board verkabeln und alle Verbindungen zu und von deinem Effektsetup in einem praktischen Modul organisieren. Die RockBoard® MODs bieten einen zentralen Zugangspunkt vom Instrument zum Verstärker sowie eine praktische und einfache Stromversorgung des Boards über einen IEC- und einen 2,1 x 5,5 Barrel-Through-Stromanschluss. Das RockBoard® MOD 1 V2 ist eine Pass-Through-Box, die speziell für Gitarristen und Bassisten entwickelt wurde. Du kannst das MOD 1 V2 nutzen um mehrere Pedale deines Setups im Front End und im Effekt-Loop des Verstärkers zu postieren (4-Kabel Methode) oder die vier TRS-Anschlüsse als zentralen Zugang und Ausgang des Boards nutzen. Die XLR-Through-Verbindung kann als Signalausgang vom Pedalboard zum Mischpult oder zur PA verwendet werden.
- All-in-One Patchbay für Pedalboards
- passend für MOD slots in RockBoard Pedalboards
- kompatibel mit einer weiten Reihe and anderen Pedalboards
- fungiert als zentraler Zugangspunkt zu deinem Effekt Setup
- etabliert klare Kabelwege zum und vom Pedalboard
- abnehmbare Frontplatte für Montage auf oder unter Pedalboards
- 5 x 6,3 mm TRS thru
- 1 x XLR thru (männlich vorne / weiblich hinten)
- 1 x DC 2,1 x 5,5 mm barrel thru
- 1 x AC IEC thru (male front / female back)
- alle Anschlüsse gespiegelt auf der Rückseite
- Abmessungen exkl. Frontplatte (B x T x H): 160 x 60 x 33 mm
- Abmessungen der Frontplatte (B x H): 175 x 48 mm
- Gewicht 450 g
- inkl. Montageschrauben, Kontermuttern und TX Schlüssel

The improved RockBoard® MODs V2 are simple all-in-one patchbays for RockBoard pedalboards with a new, refreshed design, and compact housing. Utilizing the MOD slot on all new RockBoards® (except the DUO series), they provide various cable connections to fit a wide variety of needs as a convenient patchbay. With the RockBoard® MODs, you can permanently connect your pedals underneath your board and organize all connections to and from your effects setup in one convenient module. The RockBoard® MODs provide a central access point from your instrument to your amp, as well as your power supply via IEC, and a 2.1 x 5.5 barrel thru power connector. The RockBoard® MOD 1 V2 is a pass-thru box especially designed for guitar and bass players. It can also be used to run several pedals from your board through the effects loop of your amp, or as a central access point to your pedalboard via its 4x TRS thru connections. The XLR thru connection can be used as signal output from your pedalboard to the console or PA.
- all-in-one patchbay for pedalboards 
- fits MOD slots in RockBoard pedalboards
- compatible with a wide variety of other pedalboards
- acts as the central access point to your effects setup
- establishes clean cable paths to and from the pedal board
- detachable front plate for mounting on top or underneath pedalboards
- 5 x 6,3 mm / ¼" TRS thru
- 1 x XLR thru (male front / female back)
- 1 x DC 2,1 x 5,5 mm barrel thru
- 1 x AC IEC thru (male front / female back)
- all connections mirrored on the backside
- dimensions excl. front plate (W x D x H): 160 x 60 x 33 mm / 6 19/64" x 2 23/64" x 1 19/64"
- dimensions of the front plate (W x H): 175 x 48 mm / 6 57/64" x 1 57/64"
- weight 450 g / 0.99 lbs
- incl. mounting screws, counter nuts, and TX wrench

All-in-One TRS & XLR, IEC & Barrel Patchbay

Let's rock !

Vincent Maranto

In Aufnahmestudios werden häufig Rackmount-Vocal-Channels“ verwendet - ein Mikrofonvorverstärker, ein Kompressor und ein EQ in einem Gerät als Front-End für Gesangsaufnahmen.

Der Diamond Compressor ist unsere Interpretation eines „Gitarrenkanals“ - ein Dynamik- und Klangformungswerkzeug für den Live- und Studioeinsatz - mit rauscharmer, ultra-linearer Signalpufferung, sanfter opto-basierter Kompression und einem vielseitigen „Tilt“-EQ, der die gesamte Frequenzbalance musikalisch verschiebt.

Alles in einem benutzerfreundlichen 3-Regler-Paket - nur Comp, EQ und Volume.

Recording studios often use rackmount 'vocal channels' - a mic preamp, compressor, and EQ all in one unit as a front end for vocal recording.

The Diamond Compressor is our take on a 'guitar channel' - a dynamics and tone shaping tool for live and studio use - with low-noise, ultra-linear signal buffering, smooth opto-based compression, and a versatile 'tilt' EQ that musically shifts overall frequency balance.

All in a user-friendly 3-control package - just Comp, EQ and Volume.

Diamond Pedals

Demo by Trevor Dick

Demo by Pedalicious

Review by OVNI LABS

CPR-1

ch ray

Reverb- und Tremolo-Effekte krönen das Pedalboard eines jeden Spielers. Das Zoma ist mehr als nur ein Pedal - es ist Ihre Signatur und Keeleys hochwertigstes Pro Reverb & Tremolo aller Zeiten. Vertrauen Sie auf Keeley Reverbs für einen inspirierenden „always-on“-Sound und vokalähnliche Tremolos für ein unwirkliches Klangerlebnis.

Reverb and tremolo effects crown any player's pedalboard. The Zoma is more than just a pedal – it’s your signature and Keeley's most high-fidelity pro Reverb & Tremolo ever. Trust Keeley reverbs for an inspiring "always-on" sound and vocal-like tremolos to give you an unreal sonic experience.

Keeley Electronics

Demo by Mark Hopkins

Review by guitar pedal X

Review by Guitar Bomb

Zoma

Scott Smith

Anhand der Spezifikationen des in den 1960ern vorgestellten VOX-Pedals bietet dieses Wah-Wah denselben legendären Sound. Neu sind der Netzteilanschluss und die gepufferte Eingangsbuchse, die eine Klangfärbung des Gitarrensignals bei ausgeschaltetem Pedal verhindert. Die Induktionsspule dieses Pedals wurde ganz klar vom VOX-Original inspiriert und bietet eine entsprechend größere Dynamik und einen fetteren Sound. Diese Neuauflage ist besonders für Gitarristen aller Genres gedacht, deren Signalweg ohne Wah-Pedal unvollständig wäre.

Based on the specifications of the original pedal developed by VOX in the ’60s, the new Wah-Wah offers guitarists the same legendary tone with the addition of AC power capability and a buffered input jack for preserving the unprocessed guitar tone when the pedal is not engaged. The pedal’s inductor has undergone a redesign to be closer in specification to the original VOX wah inductors, for improved dynamics and tone. These additions will benefit players of all genres who use a wah pedal as an integral part of their sound.

Review by musicradar

Review by bonedo

Demo by 3rdStoreyChemist

V847 Wah Pedal

The Protein is based around modified versions of two well-respected drive pedal circuits: the ‘Blue’ side is based on a 1990’s Marshall Bluesbreaker but has a tweaked tone control and extra output, while the ‘Green’ side takes its cue from that Nashville session favourite the Nobels ODR-1. 

Browne Amps

Review by ThatGuitarLover.com 

Review by Guitar World 

Demo by Alberto Barrero

Demo by Buddy Blues 

Protein

Comprised of photocells, a bulb, original NOS 2SC828 transistors and carbon comp resistors, the RetroVibe delivers the majestic sounds of the best Uni-Vibe pedals from back in the day, but housed in a modern pedalboard-friendly enclosure and featuring standard 9V DC operation internally lifted to 15V DC.

Choose between the Vibrato and Chorus settings and navigate from slow-rate wavy sounds all the way to fast Leslie-speaker effects!

Use it with any common passive 10k Expression pedal in conjunction with a standard TRS cable for real-time Speed control.

Jam Pedals

Review by Musiker-Board

Demo by Mikel Bluni

RetroVibe mk2

PedalSafe Type C

QuickMount Type C

Pedalmontageplatte für große vertikale Pedale

Pedal Mounting Plate For Large Vertical Pedals

Schutzabdeckung & RockBoard-Montageplatte für große vertikale Pedale

Protective Cover & RockBoard Mounting Plate For Large Vertical Pedals

Schutzabdeckung & universelle Montageplatte für große vertikale Pedale

Protective Cover & Universal Mounting Plate For Large Vertical Pedals

Das Halo Core ist eine reduzierte Version des kultigen Halo-Delays von Keeley und bietet den unglaublichen Sound von Andy Timmons mit einer vereinfachten Benutzeroberfläche. Mit Keeleys neuester DSP-Technologie liefert das Halo Core eine unverfälschte Klangqualität und vielseitige Delay-Optionen, darunter die klassischen Halo-, Viertelnoten- und punktierten Achtelnoten-Modi.
Der geheimnisvoll klingende „Halo“-Effekt von Andy Timmons ist ein modulierter Dual-Echo-Sound, der lange Zeit von dem Klangzauberer selbst geheim gehalten wurde. Andy Timmons hat Jahrzehnte damit verbracht, die Klänge, die Sie jetzt mit dem HALO Core erhalten können, zu kombinieren und zu entwickeln.
Die Noten tanzen rhythmisch und erzeugen fast einen diffusen Nachhall. Diese Noten werden durch bandähnliche Effekte wie Modulation, Sättigung und Kompression verbunden. Die Ergebnisse sind atemberaubend.
Entdecken Sie das Neueste von Keeley Electronics: den HALO Core, eine reduzierte Version von Keeleys meistverkauftem HALO Andy Timmons Dual Echo. Der HALO Core hat drei Modi: Andy's kultiger ‚HALO‘ Sound, Quarter Note und jetzt auch Dotted Eighth.

The Halo Core is a streamlined version of Keeley's iconic Halo delay, offering Andy Timmons' incredible tone with a simplified control set. Powered by Keeley's latest DSP technology, the Halo Core delivers pristine sound quality and versatile delay options, including classic Halo, quarter note, and dotted eighth note modes.
Andy Timmons’ mysterious sounding “Halo” effect is a modulated dual echo sound that has long been kept a secret by the tone wizard himself. Andy spent decades combining and crafting the sounds you can now get from the HALO Core.
Notes dance rhythmically, almost creating a reverb diffusion. Those notes are held together with tape-style effects like modulation, saturation and compression. The results are stunning.
Discover the latest from Keeley Electronics: the HALO Core, a streamlined version of Keeley's top-selling HALO Andy Timmons Dual Echo. The HALO Core has three modes: Andy's iconic ‘HALO’ sound, Quarter Note, and now Dotted Eighth.

Introducing the new Keeley HALO Core | with Robert Keeley and Andy Timmons - Keeley Electronics

Keeley Halo Core Andy Timmons Signature Delay - Review - Musiker TV

Keeley Halo Core & JHS AT+ Andy Timmons Signature Pedals - Demo - Musiker TV

Keeley Halo Core - Demo - Musiker TV

Demo by THE PEDAL COLLABORATIVE

Halo Core

Nabil Saez

Das JHS Pedals AT ist Andy Timmons Signature Overdrive-Pedal, das Andy seinen unverwechselbaren Lead- und Rhythm Tone verleiht. Der Drive Kanal des AT + ist identisch mit dem Original-AT-Pedal. Dazu gehören Volume, EQ, Drive, Air und ein Dreiwege-Schalter für 25-Watt-, 50-Watt- oder 100-Watt-Modi. Der Volume Regler bietet dir viel Spielraum zum Spielen, während der Drive Regler einen großen Bereich von High-Gain-Blues bis hin zu donnernder Distortion bietet. Die Klangregler arbeiten zusammen, um dir die Möglichkeit zu geben, deinen Ton zu formen und perfekt in den Mix zu setzen. Der EQ arbeitet als Standard Hell / Dunkel-Regler, während der Air-Regler im oberen Bereich wie ein Präsenzregler rollt, so dass du genau die richtige Helligkeit für die Artikulation und Klarheit hast. Der Drei-Wege-Schalter gibt dir das Gefühl von verschiedenen Leistungsverstärkern. Neu beim AT + ist ein eigenständiger fußschaltbarer Boost. Da der Boost unabhängig ist, kann er alleine verwendet werden, um den Verstärker oder andere Pedale in Verbindung mit dem AT + Drive-Kanal zu betreiben.

The JHS Pedals AT is Andy Timmons signature overdrive pedal that gives Andy his unmistakable lead and rhythm tone. The drive channel of the AT+ is identical to JHS original AT pedal. They include Volume, EQ, Drive, Air, and a three-way toggle for 25-watt, 50-watt, or 100-watt modes. The Volume gives you plenty of headroom to play with, while the Drive control has a wide range from high gain blues to thunderous distortion. The tone controls work together to give you the ability to shape your tone and sit perfectly in a mix. The EQ works as a standard bright/dark tone control, while the Air control rolls in top end like a presence control so you can have just the right amount of brightness for articulation and clarity. The three-way toggle gives you the feel of different wattage amplifiers. New to the AT+ is an independent foot-switchable Boost. Since the Boost is independent, it can be used alone to drive your amp or other drive pedals in conjunction with the AT+ drive channel.

Guitar Equipment Special_ Andy Timmons - Keeley Halo Dual Echo & JHS Pedals The AT+ - Review by Darkstars.de, [03-2023]

JHS The AT+ - Review by Gitarre & Bass [DE], [12-2018]

JHS The AT+ - Review by Muzikus [CZ], [03-2019]

Andy Timmons demo of the new signature AT+ by JHS Pedals

JHS Pedals The AT+ (demo)

The AT+

PedalSafe Type B2

QuickMount Type B1

Pedal-Montageplatte für FRIEDMAN, KEELEY Halo, WAMPLER EQ, VelvetFuzz, WALRUS DeepSix, JULIA V2, 385 OD, Jupiter V2 und Mooer GL 100 Pedale

Pedal Mounting Plate for FRIEDMAN, KEELEY Halo, WAMPLER EQ, VelvetFuzz, WALRUS DeepSix, JULIA V2, 385 OD, Jupiter V2 and Mooer GL 100 pedals

Schutzabdeckung & RockBoard-Montageplatte für WALRUS ARP-87 & Monument V2 Pedale

Protective Cover & RockBoard Mounting Plate For WALRUS ARP-87 & Monument V2 pedals

Schutzabdeckung & universelle Montageplatte für WALRUS ARP-87 & Monument V2 Pedale

Protective Cover & Universal Mounting Plate For WALRUS ARP-87 & Monument V2 pedals

Joel Hingston

The Del Mar was conceived in an effort to add a Tubescreamer-style clipping stage to the Klon Centaur. I’ve always loved the clean half of the Centaur, but my favourite clipping stage has always been the articulate and detailed response of the Tubescreamer.

My engineering sensibilities at the time were perhaps somewhat naive, and my attempts to incorporate aspects of the Klon, Tubescreamer and Bluesbreaker actually resulted in something that is not exactly like any of them.

In retrospect, I think that engineering things in the “wrong" way resulted in an inadvertently unique result, which at this stage and with the benefit of hindsight, is something I’ve come to be very proud of.

Bondi Effects

Demo by Ambient Endeavors

Demo by Guitar Emerge

Del Mar Mk2

Sunface bietet viele Transistoroptionen. Es gibt nicht die BESTE. Sie sind alle sehr ähnlich, weisen aber einige Unterschiede auf, die einige für Ihre Anforderungen besser machen könnten als andere.

The Sunface has many transistor options, there is no BEST, they are all very similar but have some differences that could make some better than others for your needs.

Analogman

Sun Face (Top Jacks/DC Input)

PedalSafe Type A1.1

Schutzabdeckung & RockBoard-Montageplatte für MXR® Standardgröße und Dunlop® Echoplex Delay Pedale

Protective Cover & RockBoard Mounting Plate For MXR® standard size and Dunlop® Echoplex Delay pedals

Schutzabdeckung & universelle Montageplatte für MXR® Standardgröße und Dunlop® Echoplex Delay Pedale

Protective Cover & Universal Mounting Plate For MXR® standard size and Dunlop® Echoplex Delay pedals

Simple loop switching for your guitar pedals

High-quality true bypass strip loop control for your effects pedals.

Compact easy switching solution to keep your tone intact. 

For your simple compact board, TheGigRig QuarterMaster QMX just makes life that little bit easier.

Available in 5 different options for small to large pedalboards.

The GigRig

Demo by TheGigRig

QuarterMaster QMX-6

CIOKS

Für 7-12 FX-Pedale, 1 MOD-Slot - **470 x 330 mm / 18.50" x 12.99"** - erhältlich mit Gig Bag oder Flight Case

For 7 - 12 FX pedals, 1 MOD slot - **470 x 330 mm / 18.50" x 12.99"** - available with Gig Bag or Flight Case