andronik supersonik

SUBmarine

Dave Snippe

The Voltage Unit Meter Pedal (“VUMP”) is a guitar pedal-style level indication meter. This unit reads out signal level in the
traditional “Voltage Unit” (VU) scale, which is similar to a decibel (dB) scale, but pegged to a reference value of 0
VU=1.23VRMS. Since sound levels span many decades of pressure intensity, it is convenient to express the level in the
logarithmic dB scale. An increase of 6 dB sounds about twice as loud as the reference sound level.
The intended use for this device is to be the last “pedal” in a chain of pedals connected to an electronic instrument such
as an electric guitar or bass guitar, or microphone. It provides a convenient, local measure of your signal level just before
going to the amp or a sound board. You can also precisely equalize the volume settings of your pedals using this device. 

JoyeMusic

Official Product Video

Product Page

Review by Talk Bass.com

Manual

Analog-VUMP

ch ray

Pedal76 accurately reproduces one of the fastest and most powerful studio compressors of all time, known for having ultra-fast attack and release and adding sweet analog tone to any source. Just like in the studio, Pedal76 has Attack & Release, Ratio, and Input controls, critical for taming unwanted changes in volume on stage. Backed by over 10 years of expertise delivering premium, award-winning studio compression with the Warm Audio WA76, the Pedal76 is capable of bringing out the wide range of legendary compression tones from subtle to hard-limiting as favored by celebrated artists such as Led Zeppelin, Pink Floyd, Periphery, Jack White and many more.

Warm Audio

Demo by  TheSuperFunAwesomeHappyTimePedalShow

Review by Premier Guitar

Review by Sound on Sound

Review by bonedo

Pedal76

Jonathan Nicholson

Four different preamps in a single box in a pedalboard-friendly format.
From studio-grade clean sounds up to heavy saturations, passing through endless overdrive flavors with amp-like dynamics and harmonic content.
More than just a pedal, a real studio-in-a-box.

Jad Freer Audio 

Review by Basschat

Demo by Philip Conrad

Demo by

Capo Preamp

Tester

The micro-Thumpinator is a bandwidth optimizer designed for bass guitar. It removes the low frequency signals that are outside the range of notes produced by the instrument.

Infrasonic frequencies cannot be reproduced by standard bass cabinets but they often make amplifiers clip, especially when they are set to boost the lower frequencies. The Thumpinator filters the signal content optimising the energy delivered by the amplifier. Low-frequency clip is substantially reduced and the sound is tighter especially at high volume levels.

The micro-Thumpinator accepts instrument and line level signals. It can be used between preamplifier and amplifier, between bass and amplifier or anywhere in the effect chain (line or instrument level). It can also be connected directly to an audio interface.

SFX Sound

Demo by Paul Reich

micro-Thumpinator v2

With the TU-3W, BOSS brings Waza Craft mojo to the world’s leading stompbox tuner. At its core, the TU-3W provides rock-solid tuning equivalent to the industry-standard TU-3. In true Waza tradition, the pedal’s benchmark functionality is further enhanced with BOSS skill and craftsmanship. Pure, uncolored signal transfer is essential for a tuner, and the TU-3W features redesigned circuitry with selectable buffered or true-bypass operation and the most transparent audio pass-through possible. Packing high-end performance for discriminating players, the TU-3W delivers a premium pedal experience only available from BOSS.

BOSS

TU-3W Tuner

PedalSafe Type E1

QuickMount Type E

Pedal-Montageplatte für Standard-Boss-Pedale

Pedal Mounting Plate For Standard Boss Pedals

Schutzabdeckung & RockBoard-Montageplatte für BOSS Compact Serie, RC3 LoopStation & RC5 LoopStation Pedale

Protective Cover & RockBoard Mounting Plate For BOSS Compact Series, RC3 LoopStation & RC5 LoopStation pedals

Schutzabdeckung & universelle Montageplatte für BOSS Compact Serie, RC3 LoopStation & RC5 LoopStation Pedale

Protective Cover & Universal Mounting Plate For BOSS Compact Series, RC3 LoopStation & RC5 LoopStation pedals

Für 4-7 FX-Pedale - **470 x 142 mm / 18.50" x 5.59"** - erhältlich mit Gig Bag oder Flight Case

For 4 - 7 FX pedals - **470 x 142 mm / 18.50" x 5.59"** - available with Gig Bag or Flight Case

Der RockBoard Pedalboard Drawer ist eine simple aber extrem effiziente Lösung zum Organisieren und Verstauen von optionalem Zubehör in einem RockBoard Pedalboard. Der Pedalboard Drawer wurde entwickelt, um Zubehör wie Kabel, Plektren, Wireless Systeme und vieles mehr im MOD Slot des Pedalboards aufzubewahren. Durch den zentralen Zugang auf der Front des Pedalboards bietet der Drawer einen sichereren, sauberen und einfach zugänglichen Platz zur Aufbewahrung direkt am Setup. Durch die intelligente Arretierung der rotierenden Schublade ist eine zusätzliche Sicherung nicht notwendig.

- rotierende Schublade für RockBoard Pedalboards
- intelligenter Drehmechanismus mit sicherer Arretierung
- für Zubehör, Kabel, Wireless Systeme, Plektren, etc.
- passt in die MOD-Slot Aussparung von RockBoard Pedalboards (außer RockBoard DUO 2.0, 2.1, und 2.2)
- Material: Verstärktes Polyamid
- inkl. Montagematerial und Werkzeug
- Maße (B x T x H): 175 x 84,5 x 47 mm
- Gewicht: 150 g
- schwarz
- Hinweis: Nicht kompatibel mit den 19" Rack Panel Single oder Double (1U) - Rack Mount for RockBoard MOD

The RockBoard Pedalboard Drawer is a simple but super effective solution to organize and store optional accessories in your RockBoard pedalboard. The Pedalboard Drawer is designed to store accessories such as cables, picks, wireless systems and more directly in the MOD slot of the pedalboard. With access on the front of the pedalboard, the Drawer provides a safer, cleaner, and convenient place for storage. The Drawer opens and closes using an intelligent swivel locking mechanism.

- rotating mounting drawer for RockBoard pedalboards
- intelligent swivel locking mechanism
- for accessories, cables, wireless systems, etc.
- fits MOD slots in RockBoard pedalboards (except RockBoard DUO 2.0, 2.1, 2.2, and 2.3)
- material: reinforced polyamide
- incl. all mounting screws, counter nuts, and tools
- dimensions (W x D x H): 175 x 84.5 x 47 mm / 6 57/64" x 3 21/64" x 1 27/32"
- weight: 150 g / 0.33 lbs
- black
- Note: Not compatible with 19" Rack Panel Single or Double (1U) - Rack Mount for RockBoard MOD

Rotierende Schublade für RockBoard Pedalboards

Rotating Drawer for RockBoard Pedalboards

Die RockBoard® MOD 5 Cab SIM + DI Patchbay bietet wählbare, IR-basierte Stereo-Lautsprecher Simulation, eine aktive DI-Box, sowie eine einfache Lösung, um alle Verbindungen zu und von deinem Effekt Setup zu organisieren. Egal, ob du ein RockBoard® oder ein anderes Pedalboard einer anderen Marke verwendest - die MOD 5 eröffnet völlig neue Möglichkeiten. Mit der Speaker-Cab-Simulation und DI kannst du direkt loslegen und hast DEINEN Sound parat, unabhängig davon, welche Backline an der jeweiligen Venue zur Verfügung steht. Du möchtest deine persönliche Lieblings-Cabinet benutzen? Kein Problem, lade eine Impulse Response des Sounds in die MOD 5 und du hast sie überall dabei. Der Patchbay-Teil dient dazu, Verbindungen von unterhalb deines Pedalboards nach vorne zu leiten, um dir einen zentralen Zugangspunkt zu deinem Setup zu geben und deinen Kabelsalat aufzuräumen. Für geräuschloses Üben auf der Straße bietet der MOD 5 auch einen Kopfhörerverstärker mit einstellbarer Ausgangslautstärke.
- Cabinet Simulation & DI Patchbay
- IR basierte Lautsprecher Simulation
- 6 integrierte IRs wählbar
- Unterstützung von zusätzlichen Custom IRs (max. 1024 pts.)
- integrierte aktive DI Box
- Kopfhöhrer Verstärker
- passend für MOD Slots in RockBoard® Pedalboards
- kompatibel mit einer weiten Reihe anderer Pedalboards
- fungiert als zentraler Zugangspunkt zu deinem Effekt Setup
- etabliert klare Kabelwege zum und vom Pedalboard
- abnehmbare Frontplatte für Montage auf oder unter Pedalboards
- wählbarer MONO / STEREO Input
- wählbarer UN- / BALANCED Output
- Ground Lift Schalter
- Regler für Phones Volume
- 3 x 6,3 mm TRS Thru
- XLR DI Out
- 6.3 mm Parallel TRS Output
- 3.5 mm Stereo Kopfhöhrer Ausgang mit einstellbarer Lautstärke
- micro USB Anschluss für Firmware Updates und zum Hochladen von Custom IRs
- Stromversorgung via optionalem 9V DC Netzteil, 2.1 x 5.5 mm Hohlstecker, Polarität (-) innen
- Stromaufnahme 300 mA
- Batteriebetrieb nicht unterstützt
- Abmessungen mit Frontplatte (B x T x H) 175 x 85 x 47 mm 
- Abmessungen ohne Frontplatte (B x T x H) 160 x 85 x 33 mm
- Gewicht 470 g
- inkl. Montageschrauben, Kontermuttern und TX Schlüssel

The RockBoard® MOD 5 Cab SIM + DI Patchbay offers customizable, IR-based stereo speaker cabinet simulation, an active DI box, as well as a simple solution to organize all the connections to and from your effects setup. Whether you are using a RockBoard® or any other brand pedalboard - the MOD 5 will open completely new possibilities. The speaker cab simulation & DI let's you go direct, providing YOUR sound, whatever backline is being provided at the venue you're playing. Do you want to use your favorite cab? No problem, load an impulse response of its sound into the MOD 5 and you have it with you, wherever you go. The patchbay part is designed to route connections from underneath your pedalboard to its front, in order to give you a central access point to your setup and tidy up your connections. For silent and on the road practicing, the MOD 5 also provides a headphone amplifier with adjustable output volume.
- cabinet simulation & DI patchbay
- IR-based speaker cabinet simulation
- 6 integrated IRs selectable
- support of additional Custom IRs (max. 1024 pts.)
- integrated active DI box
- headphone amplifier
- fits MOD slots in RockBoard® pedalboards
- compatible with a wide variety of other pedalboards
- acts as the central access point to your effects setup
- establishes clean cable paths to and from the pedal board
- detachable front plate for mounting on top or underneath pedalboards
- selectable MONO / STEREO input
- selectable UN / BALANCED output
- ground lift switch
- control for Phones Volume
- 3 x 6.3 mm / ¼" TRS thru
- XLR DI Out
- 6.3 mm / ¼" Parallel TRS output
- 3.5 mm / 1/8" stereo headphone output with adjustable volume
- micro USB connection for firmware updates and loading custom IRs
- power supply via optional 9V DC power adapter, 2.1 x 5.5 mm barrel plug, polarity (-) center
- current draw 300 mA
- battery operation not supported
- dimensions with front plate (W x D x H) 175 x 85 x 47 mm / 6 57/64" x 3 11/32" x 1 27/32" 
- dimensions without front plate (W x D x H) 160 x 85 x 33 mm / 6 19/64" x 3 11/32" x 1 19/64"
- weight 470 g / 1.04 lbs.
- incl. mounting screws, counter nuts, and TX wrench

Cab SIM + DI Patchbay

Die überarbeiteten RockBoard® MODs V2 sind einfache all-in-one Patchbays für die RockBoard Pedalboard Series mit einem neuen, überarbeiteten Design und einem kompakten Gehäuse. Passend für alle neuen RockBoards® (außer der DUO-Serie) mit einem MOD-Slot, bieten sie als komfortable Patchbay verschiedene Kabelverbindungen, um eine weite Reihe von Bedürfnissen abzudecken. Mit den RockBoard® MODs kannst du deine Pedale dauerhaft unter dem Board verkabeln und alle Verbindungen zu und von deinem Effektsetup in einem praktischen Modul organisieren. Die RockBoard® MODs bieten einen zentralen Zugangspunkt vom Instrument zum Verstärker sowie eine praktische und einfache Stromversorgung des Boards über einen IEC- und einen 2,1 x 5,5 Barrel-Through-Stromanschluss. Das RockBoard® MOD 1 V2 ist eine Pass-Through-Box, die speziell für Gitarristen und Bassisten entwickelt wurde. Du kannst das MOD 1 V2 nutzen um mehrere Pedale deines Setups im Front End und im Effekt-Loop des Verstärkers zu postieren (4-Kabel Methode) oder die vier TRS-Anschlüsse als zentralen Zugang und Ausgang des Boards nutzen. Die XLR-Through-Verbindung kann als Signalausgang vom Pedalboard zum Mischpult oder zur PA verwendet werden.
- All-in-One Patchbay für Pedalboards
- passend für MOD slots in RockBoard Pedalboards
- kompatibel mit einer weiten Reihe and anderen Pedalboards
- fungiert als zentraler Zugangspunkt zu deinem Effekt Setup
- etabliert klare Kabelwege zum und vom Pedalboard
- abnehmbare Frontplatte für Montage auf oder unter Pedalboards
- 5 x 6,3 mm TRS thru
- 1 x XLR thru (männlich vorne / weiblich hinten)
- 1 x DC 2,1 x 5,5 mm barrel thru
- 1 x AC IEC thru (male front / female back)
- alle Anschlüsse gespiegelt auf der Rückseite
- Abmessungen exkl. Frontplatte (B x T x H): 160 x 60 x 33 mm
- Abmessungen der Frontplatte (B x H): 175 x 48 mm
- Gewicht 450 g
- inkl. Montageschrauben, Kontermuttern und TX Schlüssel

The improved RockBoard® MODs V2 are simple all-in-one patchbays for RockBoard pedalboards with a new, refreshed design, and compact housing. Utilizing the MOD slot on all new RockBoards® (except the DUO series), they provide various cable connections to fit a wide variety of needs as a convenient patchbay. With the RockBoard® MODs, you can permanently connect your pedals underneath your board and organize all connections to and from your effects setup in one convenient module. The RockBoard® MODs provide a central access point from your instrument to your amp, as well as your power supply via IEC, and a 2.1 x 5.5 barrel thru power connector. The RockBoard® MOD 1 V2 is a pass-thru box especially designed for guitar and bass players. It can also be used to run several pedals from your board through the effects loop of your amp, or as a central access point to your pedalboard via its 4x TRS thru connections. The XLR thru connection can be used as signal output from your pedalboard to the console or PA.
- all-in-one patchbay for pedalboards 
- fits MOD slots in RockBoard pedalboards
- compatible with a wide variety of other pedalboards
- acts as the central access point to your effects setup
- establishes clean cable paths to and from the pedal board
- detachable front plate for mounting on top or underneath pedalboards
- 5 x 6,3 mm / ¼" TRS thru
- 1 x XLR thru (male front / female back)
- 1 x DC 2,1 x 5,5 mm barrel thru
- 1 x AC IEC thru (male front / female back)
- all connections mirrored on the backside
- dimensions excl. front plate (W x D x H): 160 x 60 x 33 mm / 6 19/64" x 2 23/64" x 1 19/64"
- dimensions of the front plate (W x H): 175 x 48 mm / 6 57/64" x 1 57/64"
- weight 450 g / 0.99 lbs
- incl. mounting screws, counter nuts, and TX wrench

All-in-One TRS & XLR, IEC & Barrel Patchbay

Die RockBoard® PowerMODs sind speziell entwickelte Class D Transistorverstärker mit denen Lautsprecherboxen direkt und ohne zusätzlichen Verstärker vom Pedalboard angesteuert werden können. Die PowerMODs bieten einen 3-Band EQ, eine schaltbare Cabinet Simulation für Fullrange Lautsprecher sowie eine Mute Funktion. Die PowerMODs können in den MOD Slots in allen RockBoard® Pedalboards (mit Ausnahme von DUO 2.0, 2.1 und 2.2) oder auf den Pedalboards von anderen Herstellern installiert und so Platz sparend in jedes denkbare System integriert werden.


- kompakter Verstärker für Pedalboards
- kann direkt auf allen RockBoard Pedalboards installiert werden, die mit einem MOD Slot ausgestattet sind, sowie auf Pedalboards von Drittanbietern
- Class D Transistorschaltung
- Leistung (@1% THD): 118 W an 4 Ohm / 70 W an 8 Ohm
- 3-Band EQ
- frontseitige Regler für Volume, Low, Mid, High
- frontseitiger Cab-Sim Schalter
- frontseitiger Mute Schalter
- frontseitiger 6,35 mm Lautsprecherausgang
- frontseitiger 3,5 mm Kopfhörerausgang
- frontseitiger 3.5 mm AUX IN Eingang für externe Audiosignale
- frontseitiger symmetrischer XLR DI Ausgang
- rückseitiger Anschluss für beiliegendes Netzteil
- rückseitiger Instrumenteneingang
- inklusive 220 - 240 VAC Netzteil, Ausgang 36 VDC, 4,16 A
- Abmessungen (L x B x H) 175 x 116 x 47 mm
- Gewicht 1,2 kg (einschließlich Netzteil)

The RockBoard® PowerMODs are specially designed Class D transistor amplifiers that can drive speaker cabinets directly from your pedalboard without an additional amplifier. The PowerMODs feature a 3-band EQ, switchable cabinet simulation for full-range speakers, and a mute function. The PowerMODs can be mounted directly into the MOD slot (available on all RockBoard® pedalboards except the DUO series) or onto pedalboards from other manufacturers, allowing for space-saving integration into any system.

- compact amplifier for pedalboards
- can be directly mounted on into all RockBoard pedalboards equipped with MOD slots or on third-party pedalboards
- solid-state design, class D amplifier circuitry
- power (@1% THD): 118 W at 4 Ohm / 70 W at 8 Ohm
- 3-band EQ
- front panel controls for Volume, Low, Mid, High
- front-mounted Cab-Sim switch
- front-mounted Mute switch
- front-mounted 6.35 mm (1/4") speaker output
- front-mounted 3.5 mm (1/8") headphone output
- front-mounted 3.5 mm (1/8") AUX IN input for external audio signals
- front-mounted balanced XLR DI output
- rear-mounted connection for included power supply adapter
- rear-mounted instrument input
- including 220 - 240 VAC power adapter, output 36 VDC, 4.16 A
- dimensions (L x W x H) 175 x 116 x 47 mm / 6.88" x 4.56" x 1.85"
- weight 1.2 kg / 2.65 lbs (including power supply)

Kompakter 150W Pedalboard Verstärker

Compact 150W Pedalboard Power Amp

Guitar ulalala

Scott Machalk

From recalling presets to tapping in tempos, MiniSwitch adds another layer of functionality to your Strymon pedals at the press of a button. 

Strymon

Demo by Sunday Tone 

Quick Start Guide

MiniSwitch

Cited as a major influence by wah masters such as Hendrix, Clapton, and Vaughn, Buddy Guy helped establish the effect as part of the blues vocabulary. To honor his contributions we have created the Buddy Guy Cry Baby Wah, featuring the Fasel Inductor for a sweet and singing top end, and two distinct user selectable wah voices—choose "DEEP" for a big and throaty growl, or "BG" for Buddy's own warm and bell-like wah tone. Convenient side-mounted LEDs indicate which mode you are in, while a separate LED indicates effect on/off. Let your guitar sing the blues in style with the Buddy-approved polka dot graphics and custom signature tread.

Dunlop

Review by Simon Bradley, musicradar.com

Demo by Guitar World

BG95 Buddy Guy Cry Baby Wah

QuickMount Type M

Pedal-Montageplatte für Dunlop Cry Baby Wah-Pedale

Pedal Mounting Plates For Dunlop Cry Baby Wah Pedals

The real McCoy! The SR-71 Blackbird™ ‘Tube Tone Engine’ is a genuine all-tube preamp in a compact pedal. Designed for great versatility, the  SR-71 adds additional clean/drive/distortion channels to vintage/boutique guitar amps or works as a professional stand-alone direct recording tube preamplifier. The clean channel possesses a beautifully pure, ‘glassy’ character and audio circuitry within the drive channel is tuned to generate a rich, full-bodied and devastatingly smooth overdrive.

Effectrode

Demo by Brett Kingman

Demo by Mike Hermans

Blackbird

The Tube-Vibe™ is a no compromise, innovative and original re-design of the classic Uni-Vibe pedal. However, instead of transistors, the Tube-Vibe utilises vacuum tubes, photocells and a pulsating filament lamp to generate exceptionally rich, swirling chorus and vibrato effects.

Review by musicradar

Demo by gilmourish

Tube Vibe

On more subtle settings the Phaseomatic tube phaser pedal creates a beautiful, natural sounding vibrato (frequency modulation) and shimmering phasing effects, utilising exactly the same one- and two-stage “Cathodyne” tube circuitry used to in those incredible vintage Magnatone® amps. However, the Phaseomatic’s all-tube circuitry has two additional Cathodyne phase inverters, which allow it to generate a much richer, deeper vibrato and even intense, deep “tunnel” phasing as well as a host of cosmic and spacious sound effects heard on many 1950′s “B” science fiction movie soundtracks.

Phaseomatic Vacuum Tube Phaser

Nicolas Wilfer

Die JHS Colour Box V2 ist ein Preamp / DI-Box nach dem Vorbild legendärer Neve Studio-Konsolen. Das Pedal wurde entwickelt um den authentischen Sound eines Instruments (oder Mikrofons) am Direct-In der Mischpulte zu reproduzieren, dabei bietet die Colour Box V2 alle Features der beliebten V1-Version und kommt zusätzlich mit einer Vielzahl an Verbesserungen und neuen Features, die das Pedal zu einem perfekten Allrounder und Always-On Pedal für alle denkbaren Instrumente und sogar für Sänger machen. Zu den neuen Features zählen eine erweiterte EQ-Sektion, ein Hi/Lo Schalter für massiven, cleanen Headroom und die Möglichkeit 48V Phantom-Power an Kondensator-Mikrofone weiterzugeben. Die Gain-Sektion (Rot) bietet Regelmöglichkeiten Master, Pre-Vol und Step. Master kontrolliert das Gesamt-Volume des Pedals, Pre-Vol arbeitet als Gain-Regler zwischen den beiden internen Gain Stages und bietet bei Bedarf eine Verzerrung, die von leichten Break-Up-Sounds bis zu Fuzz reicht. Der Step-Regler verändert das Gain der Preamp Stages in fünf Schritten. Der Hi/Lo Schalter verändert den cleanen Headroom des Pedals, der -20 dB Pad Schalter passt den Input bei Bedarf an Mikrofone mit einem hohen Ausgangspegel an. Die EQ-Sektion (Blau) wurden neben den bekannten Regler für Treble, Middle und Bass (+/- 17 dB Cut / Boost in jedem Band) um drei Shift-Regler erweitert, die den Frequenzbereich der einzelnen Regler anpassen. Die Hi-Pass-Sektion wird über den Kippschalter aktiviert. Um das Pedal so flexibel wie möglich zu halten steht ein kombinierter XLR/TRS Input zur Verfügung.

The JHS Colour Box V2 has all the same functionality of the popular V1 version with many new and improved additions like expanded EQ controls, a Hi/Lo switch for massive clean headroom, and the ability to pass phantom power to your condenser mics. The Gain section in red has three controls: Master, Pre-Vol, and Step. The Master volume controls the overall volume of the unit. The Pre-Vol controls the amount of gain between the two internal gain stages. This acts as a "drive" or "gain" control, adding more grit, distortion, and even fuzz as you increase the gain. The Step control increases the gain of each preamp stage in five stages. Rotating the Step knob from left-to-right will increase the gain by the following: 1st is +18 dB, 2nd is +23 dB, 3rd is +28 dB, 4th is +33 dB, 5th is +39 dB. The JHS Colour Box V2 has a new Hi/Lo switch to control the amount of clean headroom you have available. In the Lo mode, you will easily be able to get ultra clean sounds without breakup. Lo Mode is excellent for tone shaping when distortion is not needed. In the Hi mode, the Colour Box V2 will distort much more readily, giving you a broad spectrum of overdrive, distortion, and fuzz sounds. In addition to the Hi / Lo gain switch, there is a -20 dB pad switch on the right side of the Colour Box V2. This function only works when in XLR input mode and can help tame the volume for high output microphones. The EQ section in blue has three new Shift controls correlating to its standard Treble, Middle and Bass controls. The Shift knobs adjust the range of frequencies that the Treble, Middle, and Bass knobs control. The center frequencies for the Shift knobs are Treble 10kHz, Middle 1kHz, and Bass 120Hz, while the Treble, Middle, and Bass knobs boost or cut with +/- 17 dB of control. If you want to boost high-mid frequencies, turn the Mid Shift knob to 3 o'clock or above and increase the Middle knob above 12 o'clock. If you want to cut upper treble frequencies, turn the Treble Shift knob to 3 o'clock or above and set the Treble knob below 12 o'clock. The Shift knobs give you precision control over the EQ for anything you put through the Colour Box V2. The Hi-Pass section is enabled by the toggle switch below the Hi-Pass knob. Just flip it up to engage the Hi-Pass knob, which spans from 60Hz to 800Hz with a 6dB per octave slope. The Colour Box V2 has a combination XLR and 1/4" input jack to use either an instrument or microphone. Select your input with the input selector switch on the right side of the pedal labeled INST/XLR.

Official Product Page

JHS Colour Box: A 1073 You Can Take Anywhere - JHS Pedals

Colour Box V2 10 Year Anniversary

Demo by Joe Perkins

Review by Anatomy of Guitar Tone

Mercury Tube Fuzz

Ruben Shannon

The Effectrode® ‘LA-1A’ Leveling Amplifier is a high-end, studio-grade vacuum tube compressor in a pedal. Whisper-quiet operation and a wide, wide dynamic range make this tone-tool an unparalleled tone enhancer on stage and in the studio—its natural warmth and clarity are unmatched.

Review by CompressorPedalReviews

Demo by Electric Mojo Guitars

Review by loopersparadise

LA1A Levelling Amplifier

The Fire Bottle™ is an all-tube booster specially designed to enhance the tone of single coil pickups. With up to 30dB of gain on tap, this powerful boost pedal can push the input stage of a tube amp into beautiful breakup and rich overdrive, creating glassy, bolder, larger-than-life Stevie Ray Vaughan Strat® guitar sounds.

Review by Musiker-Board

Fire Bottle

The Delta-Trem™ authentically recreates the alluring, hypnotic tone and feel of vintage guitar amp tremolo in S-T-E-R-E-O! This is accomplished using vacuum tubes and an archaic, long forgotten electronic component known as a ‘Raysistor’, essentially a tiny filament lamp and photocell housed together in a small metal can. The combination of Raysistor and all-tube circuitry tube creates an exceptionally smooth, rich and musical tremolo effect that blends well with clean and overdriven guitar sounds. The true stereo signal path allows the Delta-Trem to operate as a mono tremolo with a single guitar amp or into two amps, where the sound ping-pongs between them creating a huge, 3-D, spacious tone.

Demo by DMTR Pedal Shop

Delta-Trem

The Blue Bottle™ Inductorized Booster pedal has been custom designed for blues/rock guitarist John Verity to enable him to achieve a fatter, more bluesy B.B. King ‘335’ tones from his Strat-type guitars. It’s the perfect vintage mid-boost—never too aggressive or over-the-top—for low output single coil pickups.

Review by Guitar World

Demo by John Verity

Blue Bottle

The Replicator D’Luxe is a sum up from all the knowledge, we have built up over the years, making
Tape delays.
it is a 2 head machine. The drive mechanism has been updated with a noiseless belt drive. A tape lock/release mechanism is added, to make the pinch wheel and tape last longer and electronics has been tuned to perfection.

T-Rex

Demo by Martin Klaja's Guitarchannel

Demo by Duskmos

Demo by T-Rex Effects

Review by The Gear Page

Review by GEOFF KING, mixdownmag.com.au

Replicator D'LUXE

Der Heilige Gral unter den Gitarrenhall-Effekten, der Federhall im Fender®-Stil, wurde endlich mit modernen Funktionen neu aufgelegt!
Teste ihn und entdecke, warum die meisten Surf-Gitarristen und die wirklich Hallsüchtigen auf SurfyBear setzen.

The Holy Grail of guitar reverb effects, the Fender®-style spring reverb, has been finally revisited with modern features!
Try it and discover why most surf guitarists and the truly reverb addicted are turning to SurfyBear.

Surfy Industries

Demo by R.J. Ronquillo

Review by TapeOp

Surfybear Metal Reverb

Für 15-25 FX-Pedale, 6 MOD-Slots – zwei Ebenen - **826 x 498 mm / 32.52" x 19.61"** - erhältlich mit Gig Bag oder Flight Case

For 15 - 25 FX pedals, 6 MOD slots, two levels - **826 x 498 mm / 32.52" x 19.61"** - available with Gig Bag or Flight Case

New Pedal Board

Caleb Harding

For ultimate swells and control the Xotic Volume Pedal uses high quality audio potentiometers to retain your tone throughout the entire frequency spectrum.

Xotic

XVP-25K

It's a much, much smaller than the ST-1 at only 3.9" wide x 4" deep, and more intelligent version of the epic Supa-Trem1. Sporting True-Bypass,Tap-Tempo, external Tap jack, Half/Double hold feature, up to 15dB boost, true Square, Sine, and the natural heartbeat-like Warble wave-forms! It also can do speeds so slow that a full cycle takes around 10 seconds, and fast speeds beyond 220bpm. The heart of the ST-1 is still there, the warm Analog Devices JFET preamp. And this pedal is so small it will fit in your pocket, and with its top-mounted jacks, will fit in any little spot on your board. Don't forget, just like the ST-1, the Jr also works as an incredible clean boost with the Mix control turned down!

Fulltone

Demo by PJ and the Beard

Review by Gearnews

Supa-Trem Jr

Die StageBug SB-2 ist eine kompakte passive Direktbox, die sich perfekt für aktive Bässe und Keyboards eignet. Sie ist klein genug, um in einem Instrumentenkoffer Platz zu finden, und verfügt über eine Stereo-Mono-Mischfunktion, um Mischpultkanäle einzusparen.

The StageBug SB-2 is a compact passive direct box that is perfect for active basses and keyboards, is small enough to fit inside an instrument case, and features a stereo to mono mix function to save mixer channels.

Radial Engineering

Demo by Want 2 Check

Demo by Chris Lang Music

Review by TalkBass

Stagebug SB-2

Hey Kumpel! Willkommen zum neuen Avalanche Run™ Stereo Reverb und Delay mit Tap Tempo! Der Avalanche Run wurde mit dem Ziel entwickelt, die schwebenden Ambient-Töne des Dispatch Masters auf das nächste Level zu heben und dabei benutzerfreundlich und raffiniert zu halten. Der Avalanche Run ist ein verträumtes Sonic Discovery-Device mit bis zu 2 Sekunden Delay-Zeit und einem üppigen Stereo-Reverb. Es bietet vollständige Kontrolle über die Verzögerungszeit, Wiederholungen, Mix und Voice (mit dem Tone Regler), sowie Kontrolle über die Hallfahnen-Länge und Reverb Mix. Es kann in einem von 3 verschiedenen Modi betrieben werden: Normal, Reverse und Swell. Im "Normal" -Modus fungiert der Avalanche-Run als direktes Delay und Reverb. Im "Reverse" -Modus ist die Delay Spur umgekehrt und der Reverb bleibt im normalen Modus. Im "Swell" -Modus reagiert der Avalanche Run auf deine Picking-Dynamik und fügt dem gesamten Signalweg einen Volume Swell hinzu, ähnlich wie beim manuellen Auf- und Zudrehen des Volume Reglers deiner Gitarre. Ausgestattet mit einer Kombination aus True Bypass und Buffered Bypass mit Trails-Funktion wird auch das Avalanche Run in Handarbeit in Ohio/USA hergestellt. Das Avalanche V2 verfügt über einen geräuschlosen, relais-basierten Soft-Touch Fußschalter. Audiosignale haben keinen Durchgang, wenn das Gerät nicht mit Strom versorgt wird.

Hey buddy! Welcome to your new Avalanche Run™Stereo Reverb and Delay with Tap Tempo! The Avalanche Run was developed with one goal in mind: to take the floating ambient tones of our Dispatch Master to the next level while still keeping it user friendly and refined. The Avalanche Run is a dreamy sonic discovery device with up to 2 seconds of delay time and a lush stereo reverb. It features complete control over delay time, repeats, mixand voice (with the tone control), as well as control over the reverb length and mix. It can run in one of 3 different modes: Normal, Reverse and Swell. In “Normal”mode, the Avalanche Run functions as a straightforward delay and reverb. In “Reverse”mode, the delay line is in reverse and the reverb remains in normal mode. In “Swell”mode, the Avalanche Run reacts to your picking dynamics and adds a volume swell to the entire signal path much like manually raising and lowering the volume of your guitar. Equipped with True or Buffered with trails Bypass, the Avalanche Run is hand made in Ohio, USA. The Avalanche Run V2 uses silent relay-based soft touch switching. Audio will not pass without power.

EarthQuaker Devices

Demo by Ally Amaral (EarthQuaker Devices)

Video By EarthQuakerDevices

Demo by Knobs

EarthQuaker Devices Avalanche Run v2 Stereo Reverb & Delay - EarthQuakerDevices

Review by Mod Wiggler

Avalanche Run V2, Purple Sparkle (Gear Hero Exclusive)

Michael Hodgson

Der EP-25K verfügt über ein 25-kOhm-Potentiometer, das von einigen Geräten benötigt wird, im Gegensatz zum 10-kOhm-Potentiometer des Mission EP-1. Über die beiden isolierten Ausgänge lassen sich zwei Effekte gleichzeitig steuern.

The EP-25K features a 25K Ohm potentiometer that is required by some devices compared to the 10K potentiometer in the Mission EP-1. The two isolated outputs can be used to control two effects simultaneously.

Mission Engineering

Demo by Sean Pierce Johnson

EP-25K Expression pedal

Expressionator

Mit der polyphonen Rainbow Machine stellt EarthQuaker Devices einen eigenwilligen, digitalen „Pitch-Shifting-Synthesizer“ vor, der speziell für experimentell veranlagte Musiker und „Noise-Fans“ entwickelt wurde. Die Rainbow Machine erzeugt mit digitalen Oszillatoren wilde, Intervalle und Pitch-Shiftings, für nie zuvor gehörte Harmonien und Disharmonien. Mit Reglern für Pitch, Primary, Secondary, Tracking, Magic und Tone ist das Pedal üppig ausgestattet. Außerdem verfügt die Rainbow Machine über einen Anschluss für ein Expression-Pedal sowie einen zusätzlichen „Magic“-Fußschalter. Die Rainbow Machine ist polyphon spielbar und eignet sich für Gitarre, Bass, Gesang, Keyboards und weitere Instrumente. Es verfügt über eine verbesserte Schaltung für weniger Nebengeräusche und verbesserte Leistung mit höherem Output und niedrigerem Signal-to-Noise Ratio. Darüber hinaus können nun die Activate und Magic Fußschalter im Latching sowie Momentary Modus genutzt werden, indem sie einfach gedrückt gehalten werden. So kann der gewünschte Effekt genau so lange genutzt werden, wie gewünscht. Die Rainbow Machine verfügt über True Bypass und wird handgefertigt in Ohio, USA.

With the Rainbow Machine EarthQuaker Devices delivers a unique digital pitch shifting synthesizer specially developed for experimenters and noise makers. The Rainbow Machine uses digital oscillators to produce wild intervals and pitch shiftings for never heard before harmonies and dissonances. The pedal is equipped with controls for Pitch, Primary, Secondary, Tracking, Magic and Tone. In addition, the Rainbow Machine features an expression pedal input jack as well as a “Magic” footswitch. The Rainbow Machine is polyphonic and works well with guitars, basses, vocals, keyboards and other instruments. It has an improved circuitry for lower noise and enhanced performance and higher output for improved signal-to-noise ratio. Also the Activate and Magic footswitches can be activated in standard latching operation or in momentary operation, by just holding the footswitch down for as long as you’d use the effect. The Rainbow Machine is true bypass and is hand made in Ohio, USA,

EarthQuaker Devices Rainbow Machine V2 - Official Guitar Demo

EarthQuaker Devices Rainbow Machine V2 - Official Bass Demo

Best Ambient Sound in the EarthQuaker Devices Rainbow Machine - The Pedal Zone

Rainbow Machine

QuickMount Type C

Pedalmontageplatte für große vertikale Pedale

Pedal Mounting Plate For Large Vertical Pedals

Basierend auf der gleichen proprietären DSP-Architektur wie der Earthquaker Smash-Hit Avalanche Run, ist Pyramids ein Stereo-Flanger mit fünf benutzerdefinierbaren Presets (eine Neuheit für EarthQuaker Devices!), Acht Flanger-Modi, Tap-Tempo mit Unterteilungen, ein Multifunktions Modify Regler, positive und negatives Feedback und ein variabler Mix-Regler, die man nicht jeden Tag auf einem Flanger findet. Der "Activate" -Fußschalter bietet die exklusive Flexi-Switch -Technologie von EarthQuaker Devices. Diese Relay-basierte True-Bypass-Schaltung ermöglicht einen Momentary oder Latching Betrieb des Pyramids, wodurch es einfacher denn je ist, den Effekt zu nutzen, um einzelne Noten oder Phrasen zu verzieren!

Built upon the same proprietary DSP architecture as the smash-hit Avalanche Run, Pyramids is a Stereo Flanging Device with five user-definable presets (a first for any EarthQuaker Devices pedal!), eight flanger modes, tap tempo, tap subdivision, a multifunction Modify control, positive and negative feedback, and a variable Mix control, which is something you don’t see on a flanger every day. Pyramids “Activate” footswitch features EarthQuaker Devices’ exclusive Flexi-Switch technology. This relay-based true-bypass switching platform allows for momentary or latching operation, making it easier than ever to engage the effect to bedazzle individual notes or phrases!

EarthQuaker Devices Pyramids - Official Demo

EarthQuaker Devices Pyramids - Demo Video - Pedal of the Day

EarthQuaker Devices Pyramids - Review by Gitarre & Bass [DE], [02-2019]

EarthQuaker Devices Pyramids - Review by GuitarWorld [EN]

Flanger Pyramids

Der Data Corrupter ist ein “wilder, aber reproduzierbarer” drei-stimmiger, modulierter, monophoner harmonizierender PLL (Phasenregelschleifen), der dein Eingangssignal nimmt und es „brutal in einen schmetternden Square Wave Fuzz Tone verstärkt, diesen multipliziert, herunterbricht und moduliert“ um dir harmonisch komplexe, expressive anschlags-dynamische Analog-Synth Tones, mit bis zu drei Oktaven unter (oder über) dem Originalsignal plus zusätzlichen Harmonien liefert. Um die verkorkste Maschine, die im Mainframe des Data Corrupters schlummert zu erwecken, stelle den Subharmonic Root Schalter auf Oscillator und versuche dich nicht von der sonaren Malware, die du gerade auf deinem Setup installiert hast abzuwenden. Der Data Corrupter nimmt dein Signal in die Mangel und verdreht es in die Summe und die Differenz aus Master Oscillator und Subharmonic mit Frequenzmodulation auf den oberen und unteren Oktaven.

The Data Corrupter is a “wild, yet repeatable” three-voice Modulated Monophonic Harmonizing PLL (phase-locked loop)  that takes your input signal and “brutally amplifies it into a crushing square wave fuzz tone that is then multiplied, divided, and modulated” to create a harmonically complex, expressive, and touch-responsive analog synth tone up to three octaves below (or above) the original, plus additional harmonies. To unleash the cracked machine lurking within the Data Corrupter mainframe, set the Subharmonic Root switch to Oscillator and try not to look away as the sonic malware you just installed mangles your input signal into the sum and difference of both the Master Oscillator and Subharmonic with the Frequency Modulator applied to the upper and lower octaves.

EarthQuaker Devices Data Corrupter - Demo Video - Reverb

EarthQuaker Devices Data Corrupter - Demo Video - Pedal Of The Day

EarthQuaker Devices Data Corrupter - Demo / Review Video - Knobs

EarthQuaker Devices Data Corrupter - Official Demo

EarthQuaker Devices Data Corrupter - Demo / Test Video - Vintage King

EarthQuaker Devices Data Corrupter - Demo Video - ThePedalZone

EarthQuaker Devices Data Corrupter - Demo Video - ProGuitarShopDemos

EarthQuaker Devices Data Corrupter - Demo Video - Pedals And Effects

Data Corrupter Special Edition

Bows Germanium Preamp

QuickMount Type B1

Pedal-Montageplatte für FRIEDMAN, KEELEY Halo, WAMPLER EQ, VelvetFuzz, WALRUS DeepSix, JULIA V2, 385 OD, Jupiter V2 und Mooer GL 100 Pedale

Pedal Mounting Plate for FRIEDMAN, KEELEY Halo, WAMPLER EQ, VelvetFuzz, WALRUS DeepSix, JULIA V2, 385 OD, Jupiter V2 and Mooer GL 100 pedals

Say hello to the world’s most compact reorderable audio loop switcher.

A fully analog stereo loop switcher designed to break boundaries. 
Each stereo loop can be broken up into 2x mono loops with an Y-cable and in the looper used as 2x complete independent mono loops (Y-TRS-Cables). As these cannot be displayed in this tool (but often used to double the loops on big boards) we configured in this tool 3 stereo connections as 6x mono loops. 

ML10X is the answer for today's musicians.

Morningstar Engineering

Review by 

Demo by 

ML10X (5 Stereo Loop)

Paul De maio

MC8 Pro

TU-3S Tuner

max penterman

From light Lo-Fi modulation all the way to the piercing sound of infinity ring-modulation, the Warm Audio RingerBringer accurately recreates the ultimate all-analog ring modulation effect used for experimental tones. Like the original, loved by artists like Jeff Beck, Radiohead, Omar Rodríguez-López, Trent Reznor, and many more, RingerBringer delivers the original distinct set of controls, extensive in/out options, and rich sonic textures to inspire boundless sonic experimentation.