The H24 is a steep high-pass filter pedal by Sine Effect Electronics.

This filter pedal has an adjustable frequency of 25-400Hz, and a slope of 24dB/octave (4th-order).

This pedal is ideal for electric bassists and guitarists who wish to tighten up their low-end. The pedal outputs unity gain and is designed to be low-noise.

Sine Effect

Demo by the wetter bass

Official Product Video

Product Page

Review by Basschat

As requested by many musicians after the release of the H24 and L24 filter pedals (see my other listings), the C24 pedal combines the two and also allows a clean boost of up to +20dB.
Two adjustable 24dB/octave slopes will allow you to tighten up and boost your tone like nothing else you've heard before.

C24 High+Low Pass Filter

The nanoPara is a new 1-band parametric EQ pedal from Sine Effect Electronics. After many years of trying to fit the goods into a small 5x5cm box (1.97") - without any compromises - it has finally been accomplished!

The nanoPara is analogue, fully-parametric, True Bypass and low-noise. This pedal could be very useful for guitarists and bassists looking to adjust their tone without taking up much pedalboard space.

Review by BK Pedal Reviews

nanoPara

Die Wee D.I ist eine aktive D.I-Box mit geringem Rauschen, kompakter Größe und der Möglichkeit, entweder über +48V Phantomspeisung oder ein separates DC-Netzteil betrieben zu werden. Im Gegensatz zu passiven, preisgünstigen D.I-Boxen bietet dieses Pedal eine vollständige Frequenzwiedergabe von 10Hz bis 20KHz.

Das Wee D.I Pedal verwendet eine Neutrik-XLR-Buchse, Nichicon-Kondensatoren und einen modernen, rauscharme Operationsverstärker.

Die Masse in diesem Pedal ist dauerhaft über einen Widerstand und einen Kondensator getrennt, was die meisten Brummschleifenprobleme verringern sollte, während das Pedal korrekt funktioniert, wenn keine Schleife vorhanden ist. Die Phantomspeisung wird automatisch getrennt, wenn ein DC-Stecker eingesteckt wird.


The Wee D.I is an active D.I box with low noise, a small size and the ability to use either +48V phantom power or a standalone DC power supply. Unlike passive, inexpensive D.I boxes, this pedal has a full-spectrum frequency response from 10Hz to 20KHz.

The Wee D.I pedal uses a Neutrik XLR socket, Nichicon capacitors and a modern, low-noise op-amp.

The ground in this pedal is permanently lifted via. a resistor and a capacitor, which should mitigate the majority of ground loop issues while allowing the pedal to function correctly when there is no loop. Phantom power is automatically disconnected when a DC plug is inserted.

Wee D.I.

Das nanoGain ist ein kleines, unkompliziertes Clean-Boost-Pedal. Es verwendet einen rauscharme Operationsverstärker-Schaltung für eine zuverlässige, präzise Signalverstärkung – unabhängig von seiner geringen Größe. Das nanoGain wurde entwickelt, um ein gutes Gleichgewicht zwischen Leistung und Kosten zu erreichen.

Untergebracht in einem 5x5cm (1,97") Gehäuse bietet das nanoGain Flexibilität und Effektivität, ohne viel Platz zu beanspruchen.


The nanoGain is a small, no-nonsense clean boost pedal. The pedal uses a low-noise op-amp circuit for reliable, precise signal boosting, regardless of its small size. The nanoGain has been designed to achieve a good balance of performance with cost.

Built into a 5x5cm (1.97") enclosure, you should find the nanoDryve to be flexible and effective without taking up much space.

nanoGain Clean Boost