andronik supersonik

Guitar ulala

Tester

The original DiscumBOBulator was often heralded as being the world’s best autowah/envelope filter pedal. So how do you improve a pedal that’s already flawlessly funky? Well, start out by making the filter-triggering even better and extend the dynamic range and feel. Now triple the headroom signal, so the pedal handles the red hot signals of active bass pickups and line level inputs like a piece of cake. Finally you add an independent 10dB boost that’ll make funky solos take flight instantly, and you have the new improved DiscumBOBulator V2.

Emma Electronic

Demo by Godlyke Inc.

Demo by  Maksim Sorokin

Product Page

Review by Pedal of the Day

Review by Talk Bass.com

Review by musicradar

Manual

DiscumBOBulator v2

Nicolas Wilfer

Die JHS Colour Box V2 ist ein Preamp / DI-Box nach dem Vorbild legendärer Neve Studio-Konsolen. Das Pedal wurde entwickelt um den authentischen Sound eines Instruments (oder Mikrofons) am Direct-In der Mischpulte zu reproduzieren, dabei bietet die Colour Box V2 alle Features der beliebten V1-Version und kommt zusätzlich mit einer Vielzahl an Verbesserungen und neuen Features, die das Pedal zu einem perfekten Allrounder und Always-On Pedal für alle denkbaren Instrumente und sogar für Sänger machen. Zu den neuen Features zählen eine erweiterte EQ-Sektion, ein Hi/Lo Schalter für massiven, cleanen Headroom und die Möglichkeit 48V Phantom-Power an Kondensator-Mikrofone weiterzugeben. Die Gain-Sektion (Rot) bietet Regelmöglichkeiten Master, Pre-Vol und Step. Master kontrolliert das Gesamt-Volume des Pedals, Pre-Vol arbeitet als Gain-Regler zwischen den beiden internen Gain Stages und bietet bei Bedarf eine Verzerrung, die von leichten Break-Up-Sounds bis zu Fuzz reicht. Der Step-Regler verändert das Gain der Preamp Stages in fünf Schritten. Der Hi/Lo Schalter verändert den cleanen Headroom des Pedals, der -20 dB Pad Schalter passt den Input bei Bedarf an Mikrofone mit einem hohen Ausgangspegel an. Die EQ-Sektion (Blau) wurden neben den bekannten Regler für Treble, Middle und Bass (+/- 17 dB Cut / Boost in jedem Band) um drei Shift-Regler erweitert, die den Frequenzbereich der einzelnen Regler anpassen. Die Hi-Pass-Sektion wird über den Kippschalter aktiviert. Um das Pedal so flexibel wie möglich zu halten steht ein kombinierter XLR/TRS Input zur Verfügung.

The JHS Colour Box V2 has all the same functionality of the popular V1 version with many new and improved additions like expanded EQ controls, a Hi/Lo switch for massive clean headroom, and the ability to pass phantom power to your condenser mics. The Gain section in red has three controls: Master, Pre-Vol, and Step. The Master volume controls the overall volume of the unit. The Pre-Vol controls the amount of gain between the two internal gain stages. This acts as a "drive" or "gain" control, adding more grit, distortion, and even fuzz as you increase the gain. The Step control increases the gain of each preamp stage in five stages. Rotating the Step knob from left-to-right will increase the gain by the following: 1st is +18 dB, 2nd is +23 dB, 3rd is +28 dB, 4th is +33 dB, 5th is +39 dB. The JHS Colour Box V2 has a new Hi/Lo switch to control the amount of clean headroom you have available. In the Lo mode, you will easily be able to get ultra clean sounds without breakup. Lo Mode is excellent for tone shaping when distortion is not needed. In the Hi mode, the Colour Box V2 will distort much more readily, giving you a broad spectrum of overdrive, distortion, and fuzz sounds. In addition to the Hi / Lo gain switch, there is a -20 dB pad switch on the right side of the Colour Box V2. This function only works when in XLR input mode and can help tame the volume for high output microphones. The EQ section in blue has three new Shift controls correlating to its standard Treble, Middle and Bass controls. The Shift knobs adjust the range of frequencies that the Treble, Middle, and Bass knobs control. The center frequencies for the Shift knobs are Treble 10kHz, Middle 1kHz, and Bass 120Hz, while the Treble, Middle, and Bass knobs boost or cut with +/- 17 dB of control. If you want to boost high-mid frequencies, turn the Mid Shift knob to 3 o'clock or above and increase the Middle knob above 12 o'clock. If you want to cut upper treble frequencies, turn the Treble Shift knob to 3 o'clock or above and set the Treble knob below 12 o'clock. The Shift knobs give you precision control over the EQ for anything you put through the Colour Box V2. The Hi-Pass section is enabled by the toggle switch below the Hi-Pass knob. Just flip it up to engage the Hi-Pass knob, which spans from 60Hz to 800Hz with a 6dB per octave slope. The Colour Box V2 has a combination XLR and 1/4" input jack to use either an instrument or microphone. Select your input with the input selector switch on the right side of the pedal labeled INST/XLR.

Official Product Page

JHS Colour Box: A 1073 You Can Take Anywhere - JHS Pedals

Colour Box V2 10 Year Anniversary

Effectrode

Demo by Joe Perkins

Demo by Mike Hermans

Review by Anatomy of Guitar Tone

Mercury Tube Fuzz

Ruben Shannon

The Effectrode® ‘LA-1A’ Leveling Amplifier is a high-end, studio-grade vacuum tube compressor in a pedal. Whisper-quiet operation and a wide, wide dynamic range make this tone-tool an unparalleled tone enhancer on stage and in the studio—its natural warmth and clarity are unmatched.

Review by CompressorPedalReviews

Demo by Electric Mojo Guitars

Review by loopersparadise

LA1A Levelling Amplifier

The Fire Bottle™ is an all-tube booster specially designed to enhance the tone of single coil pickups. With up to 30dB of gain on tap, this powerful boost pedal can push the input stage of a tube amp into beautiful breakup and rich overdrive, creating glassy, bolder, larger-than-life Stevie Ray Vaughan Strat® guitar sounds.

Review by Musiker-Board

Demo by gilmourish

Fire Bottle

The Delta-Trem™ authentically recreates the alluring, hypnotic tone and feel of vintage guitar amp tremolo in S-T-E-R-E-O! This is accomplished using vacuum tubes and an archaic, long forgotten electronic component known as a ‘Raysistor’, essentially a tiny filament lamp and photocell housed together in a small metal can. The combination of Raysistor and all-tube circuitry tube creates an exceptionally smooth, rich and musical tremolo effect that blends well with clean and overdriven guitar sounds. The true stereo signal path allows the Delta-Trem to operate as a mono tremolo with a single guitar amp or into two amps, where the sound ping-pongs between them creating a huge, 3-D, spacious tone.

Demo by DMTR Pedal Shop

Delta-Trem

The Blue Bottle™ Inductorized Booster pedal has been custom designed for blues/rock guitarist John Verity to enable him to achieve a fatter, more bluesy B.B. King ‘335’ tones from his Strat-type guitars. It’s the perfect vintage mid-boost—never too aggressive or over-the-top—for low output single coil pickups.

Review by Guitar World

Demo by John Verity

Official Product Video

Blue Bottle

The Replicator D’Luxe is a sum up from all the knowledge, we have built up over the years, making
Tape delays.
it is a 2 head machine. The drive mechanism has been updated with a noiseless belt drive. A tape lock/release mechanism is added, to make the pinch wheel and tape last longer and electronics has been tuned to perfection.

T-Rex

Demo by Martin Klaja's Guitarchannel

Demo by Duskmos

Demo by T-Rex Effects

Review by The Gear Page

Review by GEOFF KING, mixdownmag.com.au

Replicator D'LUXE

Der Heilige Gral unter den Gitarrenhall-Effekten, der Federhall im Fender®-Stil, wurde endlich mit modernen Funktionen neu aufgelegt!
Teste ihn und entdecke, warum die meisten Surf-Gitarristen und die wirklich Hallsüchtigen auf SurfyBear setzen.

The Holy Grail of guitar reverb effects, the Fender®-style spring reverb, has been finally revisited with modern features!
Try it and discover why most surf guitarists and the truly reverb addicted are turning to SurfyBear.

Surfy Industries

Demo by R.J. Ronquillo

Review by TapeOp

Review by bonedo

Surfybear Metal Reverb

With the TU-3W, BOSS brings Waza Craft mojo to the world’s leading stompbox tuner. At its core, the TU-3W provides rock-solid tuning equivalent to the industry-standard TU-3. In true Waza tradition, the pedal’s benchmark functionality is further enhanced with BOSS skill and craftsmanship. Pure, uncolored signal transfer is essential for a tuner, and the TU-3W features redesigned circuitry with selectable buffered or true-bypass operation and the most transparent audio pass-through possible. Packing high-end performance for discriminating players, the TU-3W delivers a premium pedal experience only available from BOSS.

BOSS

TU-3W Tuner

PedalSafe Type E1

QuickMount Type E

Pedal-Montageplatte für Standard-Boss-Pedale

Pedal Mounting Plate For Standard Boss Pedals

Schutzabdeckung & RockBoard-Montageplatte für BOSS Compact Serie, RC3 LoopStation & RC5 LoopStation Pedale

Protective Cover & RockBoard Mounting Plate For BOSS Compact Series, RC3 LoopStation & RC5 LoopStation pedals

Schutzabdeckung & universelle Montageplatte für BOSS Compact Serie, RC3 LoopStation & RC5 LoopStation Pedale

Protective Cover & Universal Mounting Plate For BOSS Compact Series, RC3 LoopStation & RC5 LoopStation pedals

Für 10-20 FX-Pedale, 2 MOD-Slots - **828 x 330 mm / 32.60" x 12.99"** - erhältlich mit Gig Bag oder Flight Case

For 10 - 20 FX pedals, 2 MOD slots - **828 x 330 mm / 32.60" x 12.99"** - available with Gig Bag or Flight Case

Der RockBoard Pedalboard Drawer ist eine simple aber extrem effiziente Lösung zum Organisieren und Verstauen von optionalem Zubehör in einem RockBoard Pedalboard. Der Pedalboard Drawer wurde entwickelt, um Zubehör wie Kabel, Plektren, Wireless Systeme und vieles mehr im MOD Slot des Pedalboards aufzubewahren. Durch den zentralen Zugang auf der Front des Pedalboards bietet der Drawer einen sichereren, sauberen und einfach zugänglichen Platz zur Aufbewahrung direkt am Setup. Durch die intelligente Arretierung der rotierenden Schublade ist eine zusätzliche Sicherung nicht notwendig.

- rotierende Schublade für RockBoard Pedalboards
- intelligenter Drehmechanismus mit sicherer Arretierung
- für Zubehör, Kabel, Wireless Systeme, Plektren, etc.
- passt in die MOD-Slot Aussparung von RockBoard Pedalboards (außer RockBoard DUO 2.0, 2.1, und 2.2)
- Material: Verstärktes Polyamid
- inkl. Montagematerial und Werkzeug
- Maße (B x T x H): 175 x 84,5 x 47 mm
- Gewicht: 150 g
- schwarz
- Hinweis: Nicht kompatibel mit den 19" Rack Panel Single oder Double (1U) - Rack Mount for RockBoard MOD

The RockBoard Pedalboard Drawer is a simple but super effective solution to organize and store optional accessories in your RockBoard pedalboard. The Pedalboard Drawer is designed to store accessories such as cables, picks, wireless systems and more directly in the MOD slot of the pedalboard. With access on the front of the pedalboard, the Drawer provides a safer, cleaner, and convenient place for storage. The Drawer opens and closes using an intelligent swivel locking mechanism.

- rotating mounting drawer for RockBoard pedalboards
- intelligent swivel locking mechanism
- for accessories, cables, wireless systems, etc.
- fits MOD slots in RockBoard pedalboards (except RockBoard DUO 2.0, 2.1, 2.2, and 2.3)
- material: reinforced polyamide
- incl. all mounting screws, counter nuts, and tools
- dimensions (W x D x H): 175 x 84.5 x 47 mm / 6 57/64" x 3 21/64" x 1 27/32"
- weight: 150 g / 0.33 lbs
- black
- Note: Not compatible with 19" Rack Panel Single or Double (1U) - Rack Mount for RockBoard MOD

Rotierende Schublade für RockBoard Pedalboards

Rotating Drawer for RockBoard Pedalboards

Die RockBoard® MOD 5 Cab SIM + DI Patchbay bietet wählbare, IR-basierte Stereo-Lautsprecher Simulation, eine aktive DI-Box, sowie eine einfache Lösung, um alle Verbindungen zu und von deinem Effekt Setup zu organisieren. Egal, ob du ein RockBoard® oder ein anderes Pedalboard einer anderen Marke verwendest - die MOD 5 eröffnet völlig neue Möglichkeiten. Mit der Speaker-Cab-Simulation und DI kannst du direkt loslegen und hast DEINEN Sound parat, unabhängig davon, welche Backline an der jeweiligen Venue zur Verfügung steht. Du möchtest deine persönliche Lieblings-Cabinet benutzen? Kein Problem, lade eine Impulse Response des Sounds in die MOD 5 und du hast sie überall dabei. Der Patchbay-Teil dient dazu, Verbindungen von unterhalb deines Pedalboards nach vorne zu leiten, um dir einen zentralen Zugangspunkt zu deinem Setup zu geben und deinen Kabelsalat aufzuräumen. Für geräuschloses Üben auf der Straße bietet der MOD 5 auch einen Kopfhörerverstärker mit einstellbarer Ausgangslautstärke.
- Cabinet Simulation & DI Patchbay
- IR basierte Lautsprecher Simulation
- 6 integrierte IRs wählbar
- Unterstützung von zusätzlichen Custom IRs (max. 1024 pts.)
- integrierte aktive DI Box
- Kopfhöhrer Verstärker
- passend für MOD Slots in RockBoard® Pedalboards
- kompatibel mit einer weiten Reihe anderer Pedalboards
- fungiert als zentraler Zugangspunkt zu deinem Effekt Setup
- etabliert klare Kabelwege zum und vom Pedalboard
- abnehmbare Frontplatte für Montage auf oder unter Pedalboards
- wählbarer MONO / STEREO Input
- wählbarer UN- / BALANCED Output
- Ground Lift Schalter
- Regler für Phones Volume
- 3 x 6,3 mm TRS Thru
- XLR DI Out
- 6.3 mm Parallel TRS Output
- 3.5 mm Stereo Kopfhöhrer Ausgang mit einstellbarer Lautstärke
- micro USB Anschluss für Firmware Updates und zum Hochladen von Custom IRs
- Stromversorgung via optionalem 9V DC Netzteil, 2.1 x 5.5 mm Hohlstecker, Polarität (-) innen
- Stromaufnahme 300 mA
- Batteriebetrieb nicht unterstützt
- Abmessungen mit Frontplatte (B x T x H) 175 x 85 x 47 mm 
- Abmessungen ohne Frontplatte (B x T x H) 160 x 85 x 33 mm
- Gewicht 470 g
- inkl. Montageschrauben, Kontermuttern und TX Schlüssel

The RockBoard® MOD 5 Cab SIM + DI Patchbay offers customizable, IR-based stereo speaker cabinet simulation, an active DI box, as well as a simple solution to organize all the connections to and from your effects setup. Whether you are using a RockBoard® or any other brand pedalboard - the MOD 5 will open completely new possibilities. The speaker cab simulation & DI let's you go direct, providing YOUR sound, whatever backline is being provided at the venue you're playing. Do you want to use your favorite cab? No problem, load an impulse response of its sound into the MOD 5 and you have it with you, wherever you go. The patchbay part is designed to route connections from underneath your pedalboard to its front, in order to give you a central access point to your setup and tidy up your connections. For silent and on the road practicing, the MOD 5 also provides a headphone amplifier with adjustable output volume.
- cabinet simulation & DI patchbay
- IR-based speaker cabinet simulation
- 6 integrated IRs selectable
- support of additional Custom IRs (max. 1024 pts.)
- integrated active DI box
- headphone amplifier
- fits MOD slots in RockBoard® pedalboards
- compatible with a wide variety of other pedalboards
- acts as the central access point to your effects setup
- establishes clean cable paths to and from the pedal board
- detachable front plate for mounting on top or underneath pedalboards
- selectable MONO / STEREO input
- selectable UN / BALANCED output
- ground lift switch
- control for Phones Volume
- 3 x 6.3 mm / ¼" TRS thru
- XLR DI Out
- 6.3 mm / ¼" Parallel TRS output
- 3.5 mm / 1/8" stereo headphone output with adjustable volume
- micro USB connection for firmware updates and loading custom IRs
- power supply via optional 9V DC power adapter, 2.1 x 5.5 mm barrel plug, polarity (-) center
- current draw 300 mA
- battery operation not supported
- dimensions with front plate (W x D x H) 175 x 85 x 47 mm / 6 57/64" x 3 11/32" x 1 27/32" 
- dimensions without front plate (W x D x H) 160 x 85 x 33 mm / 6 19/64" x 3 11/32" x 1 19/64"
- weight 470 g / 1.04 lbs.
- incl. mounting screws, counter nuts, and TX wrench

Cab SIM + DI Patchbay

Die überarbeiteten RockBoard® MODs V2 sind einfache all-in-one Patchbays für die RockBoard Pedalboard Series mit einem neuen, überarbeiteten Design und einem kompakten Gehäuse. Passend für alle neuen RockBoards® (außer der DUO-Serie) mit einem MOD-Slot, bieten sie als komfortable Patchbay verschiedene Kabelverbindungen, um eine weite Reihe von Bedürfnissen abzudecken. Mit den RockBoard® MODs kannst du deine Pedale dauerhaft unter dem Board verkabeln und alle Verbindungen zu und von deinem Effektsetup in einem praktischen Modul organisieren. Die RockBoard® MODs bieten einen zentralen Zugangspunkt vom Instrument zum Verstärker sowie eine praktische und einfache Stromversorgung des Boards über einen IEC- und einen 2,1 x 5,5 Barrel-Through-Stromanschluss. Das RockBoard® MOD 1 V2 ist eine Pass-Through-Box, die speziell für Gitarristen und Bassisten entwickelt wurde. Du kannst das MOD 1 V2 nutzen um mehrere Pedale deines Setups im Front End und im Effekt-Loop des Verstärkers zu postieren (4-Kabel Methode) oder die vier TRS-Anschlüsse als zentralen Zugang und Ausgang des Boards nutzen. Die XLR-Through-Verbindung kann als Signalausgang vom Pedalboard zum Mischpult oder zur PA verwendet werden.
- All-in-One Patchbay für Pedalboards
- passend für MOD slots in RockBoard Pedalboards
- kompatibel mit einer weiten Reihe and anderen Pedalboards
- fungiert als zentraler Zugangspunkt zu deinem Effekt Setup
- etabliert klare Kabelwege zum und vom Pedalboard
- abnehmbare Frontplatte für Montage auf oder unter Pedalboards
- 5 x 6,3 mm TRS thru
- 1 x XLR thru (männlich vorne / weiblich hinten)
- 1 x DC 2,1 x 5,5 mm barrel thru
- 1 x AC IEC thru (male front / female back)
- alle Anschlüsse gespiegelt auf der Rückseite
- Abmessungen exkl. Frontplatte (B x T x H): 160 x 60 x 33 mm
- Abmessungen der Frontplatte (B x H): 175 x 48 mm
- Gewicht 450 g
- inkl. Montageschrauben, Kontermuttern und TX Schlüssel

The improved RockBoard® MODs V2 are simple all-in-one patchbays for RockBoard pedalboards with a new, refreshed design, and compact housing. Utilizing the MOD slot on all new RockBoards® (except the DUO series), they provide various cable connections to fit a wide variety of needs as a convenient patchbay. With the RockBoard® MODs, you can permanently connect your pedals underneath your board and organize all connections to and from your effects setup in one convenient module. The RockBoard® MODs provide a central access point from your instrument to your amp, as well as your power supply via IEC, and a 2.1 x 5.5 barrel thru power connector. The RockBoard® MOD 1 V2 is a pass-thru box especially designed for guitar and bass players. It can also be used to run several pedals from your board through the effects loop of your amp, or as a central access point to your pedalboard via its 4x TRS thru connections. The XLR thru connection can be used as signal output from your pedalboard to the console or PA.
- all-in-one patchbay for pedalboards 
- fits MOD slots in RockBoard pedalboards
- compatible with a wide variety of other pedalboards
- acts as the central access point to your effects setup
- establishes clean cable paths to and from the pedal board
- detachable front plate for mounting on top or underneath pedalboards
- 5 x 6,3 mm / ¼" TRS thru
- 1 x XLR thru (male front / female back)
- 1 x DC 2,1 x 5,5 mm barrel thru
- 1 x AC IEC thru (male front / female back)
- all connections mirrored on the backside
- dimensions excl. front plate (W x D x H): 160 x 60 x 33 mm / 6 19/64" x 2 23/64" x 1 19/64"
- dimensions of the front plate (W x H): 175 x 48 mm / 6 57/64" x 1 57/64"
- weight 450 g / 0.99 lbs
- incl. mounting screws, counter nuts, and TX wrench

All-in-One TRS & XLR, IEC & Barrel Patchbay

Die RockBoard® PowerMODs sind speziell entwickelte Class D Transistorverstärker mit denen Lautsprecherboxen direkt und ohne zusätzlichen Verstärker vom Pedalboard angesteuert werden können. Die PowerMODs bieten einen 3-Band EQ, eine schaltbare Cabinet Simulation für Fullrange Lautsprecher sowie eine Mute Funktion. Die PowerMODs können in den MOD Slots in allen RockBoard® Pedalboards (mit Ausnahme von DUO 2.0, 2.1 und 2.2) oder auf den Pedalboards von anderen Herstellern installiert und so Platz sparend in jedes denkbare System integriert werden.


- kompakter Verstärker für Pedalboards
- kann direkt auf allen RockBoard Pedalboards installiert werden, die mit einem MOD Slot ausgestattet sind, sowie auf Pedalboards von Drittanbietern
- Class D Transistorschaltung
- Leistung (@1% THD): 118 W an 4 Ohm / 70 W an 8 Ohm
- 3-Band EQ
- frontseitige Regler für Volume, Low, Mid, High
- frontseitiger Cab-Sim Schalter
- frontseitiger Mute Schalter
- frontseitiger 6,35 mm Lautsprecherausgang
- frontseitiger 3,5 mm Kopfhörerausgang
- frontseitiger 3.5 mm AUX IN Eingang für externe Audiosignale
- frontseitiger symmetrischer XLR DI Ausgang
- rückseitiger Anschluss für beiliegendes Netzteil
- rückseitiger Instrumenteneingang
- inklusive 220 - 240 VAC Netzteil, Ausgang 36 VDC, 4,16 A
- Abmessungen (L x B x H) 175 x 116 x 47 mm
- Gewicht 1,2 kg (einschließlich Netzteil)

The RockBoard® PowerMODs are specially designed Class D transistor amplifiers that can drive speaker cabinets directly from your pedalboard without an additional amplifier. The PowerMODs feature a 3-band EQ, switchable cabinet simulation for full-range speakers, and a mute function. The PowerMODs can be mounted directly into the MOD slot (available on all RockBoard® pedalboards except the DUO series) or onto pedalboards from other manufacturers, allowing for space-saving integration into any system.

- compact amplifier for pedalboards
- can be directly mounted on into all RockBoard pedalboards equipped with MOD slots or on third-party pedalboards
- solid-state design, class D amplifier circuitry
- power (@1% THD): 118 W at 4 Ohm / 70 W at 8 Ohm
- 3-band EQ
- front panel controls for Volume, Low, Mid, High
- front-mounted Cab-Sim switch
- front-mounted Mute switch
- front-mounted 6.35 mm (1/4") speaker output
- front-mounted 3.5 mm (1/8") headphone output
- front-mounted 3.5 mm (1/8") AUX IN input for external audio signals
- front-mounted balanced XLR DI output
- rear-mounted connection for included power supply adapter
- rear-mounted instrument input
- including 220 - 240 VAC power adapter, output 36 VDC, 4.16 A
- dimensions (L x W x H) 175 x 116 x 47 mm / 6.88" x 4.56" x 1.85"
- weight 1.2 kg / 2.65 lbs (including power supply)

Kompakter 150W Pedalboard Verstärker

Compact 150W Pedalboard Power Amp

Guitar ulalala

Scott Machalk

From recalling presets to tapping in tempos, MiniSwitch adds another layer of functionality to your Strymon pedals at the press of a button. 

Strymon

Demo by Sunday Tone 

Quick Start Guide

MiniSwitch

Dave Snippe

The Voltage Unit Meter Pedal (“VUMP”) is a guitar pedal-style level indication meter. This unit reads out signal level in the
traditional “Voltage Unit” (VU) scale, which is similar to a decibel (dB) scale, but pegged to a reference value of 0
VU=1.23VRMS. Since sound levels span many decades of pressure intensity, it is convenient to express the level in the
logarithmic dB scale. An increase of 6 dB sounds about twice as loud as the reference sound level.
The intended use for this device is to be the last “pedal” in a chain of pedals connected to an electronic instrument such
as an electric guitar or bass guitar, or microphone. It provides a convenient, local measure of your signal level just before
going to the amp or a sound board. You can also precisely equalize the volume settings of your pedals using this device. 

JoyeMusic

Analog-VUMP

Cited as a major influence by wah masters such as Hendrix, Clapton, and Vaughn, Buddy Guy helped establish the effect as part of the blues vocabulary. To honor his contributions we have created the Buddy Guy Cry Baby Wah, featuring the Fasel Inductor for a sweet and singing top end, and two distinct user selectable wah voices—choose "DEEP" for a big and throaty growl, or "BG" for Buddy's own warm and bell-like wah tone. Convenient side-mounted LEDs indicate which mode you are in, while a separate LED indicates effect on/off. Let your guitar sing the blues in style with the Buddy-approved polka dot graphics and custom signature tread.

Dunlop

Review by Simon Bradley, musicradar.com

Demo by Guitar World

BG95 Buddy Guy Cry Baby Wah

QuickMount Type M

Pedal-Montageplatte für Dunlop Cry Baby Wah-Pedale

Pedal Mounting Plates For Dunlop Cry Baby Wah Pedals

The real McCoy! The SR-71 Blackbird™ ‘Tube Tone Engine’ is a genuine all-tube preamp in a compact pedal. Designed for great versatility, the  SR-71 adds additional clean/drive/distortion channels to vintage/boutique guitar amps or works as a professional stand-alone direct recording tube preamplifier. The clean channel possesses a beautifully pure, ‘glassy’ character and audio circuitry within the drive channel is tuned to generate a rich, full-bodied and devastatingly smooth overdrive.

Review by Sound on Sound

Demo by Brett Kingman

Blackbird

The Tube-Vibe™ is a no compromise, innovative and original re-design of the classic Uni-Vibe pedal. However, instead of transistors, the Tube-Vibe utilises vacuum tubes, photocells and a pulsating filament lamp to generate exceptionally rich, swirling chorus and vibrato effects.

Tube Vibe

On more subtle settings the Phaseomatic tube phaser pedal creates a beautiful, natural sounding vibrato (frequency modulation) and shimmering phasing effects, utilising exactly the same one- and two-stage “Cathodyne” tube circuitry used to in those incredible vintage Magnatone® amps. However, the Phaseomatic’s all-tube circuitry has two additional Cathodyne phase inverters, which allow it to generate a much richer, deeper vibrato and even intense, deep “tunnel” phasing as well as a host of cosmic and spacious sound effects heard on many 1950′s “B” science fiction movie soundtracks.

Phaseomatic Vacuum Tube Phaser

Für 15-25 FX-Pedale, 6 MOD-Slots – zwei Ebenen - **826 x 498 mm / 32.52" x 19.61"** - erhältlich mit Gig Bag oder Flight Case

For 15 - 25 FX pedals, 6 MOD slots, two levels - **826 x 498 mm / 32.52" x 19.61"** - available with Gig Bag or Flight Case

Carmelo Cannistraro

New Pedal Board

Der PETE CORNISH G-2™ wird als der am originellsten klingende Verzerrer für Gitarristen in der Rock-Arena gepriesen. Er verfügt über eine vierstufige übersteuerte diskrete Transistor-Class-A-Schaltung mit zusätzlichen Germanium-Komponenten, die viel wärmer klingende Obertöne erzeugen als alles andere auf dem Markt. Innerhalb des riesigen Tons, der von diesem Gerät erzeugt wird, sind der ursprüngliche Gitarrensound und die Dynamik vorhanden, was einen viel musikalischeren Effekt als bei jedem anderen Distortion-Pedal erzeugt.

The PETE CORNISH G-2™ has been hailed as the most original sounding distortion unit available to guitarists in the Rock Arena. It features a four stage overdriven discrete transistor Class A circuit with additional Germanium components that generate much warmer sounding harmonics than anything else on the market. Within the huge tone generated by this unit, the original guitar sound and dynamics are present creating a much more musical effect than any other distortion pedal.

Pete Cornish

Review by Pedal PCB

Review by Audiofanzine

Demo by Simone Gianlorenzi

Demo by shnobel

Demo by Simon Gotthelf Music

Demo by MICK HAYES MUSIC TV

Paulo Damasceno Nepomuceno

Tuning used to be a necessary evil. The last barrier before you could get truly rocking. But now, tuning is ready to get blasted into the 21st century with PolyTune, the stomp-box sized tuning miracle from TC Electronic!

With PolyTune, you simply strum all strings on your guitar or bass at once, and it will immediately tell you which strings need tuning! It really is as simple as strum - tune - rock, and this quantum leap forward allows you to get in tune fast, and back to doing what you love: playing!

TC Electronic

Demo by ams.guitar

Polytune

QuickMount Type G 

Pedal-Montageplatte für Standard TC Electronic Pedale

Pedal Mounting Plate For Standard TC Electronic Pedals

The VM-PRO resolves many of the common issues with volume pedals that cause tone sucking and mismatching problems. The VM-PRO works with electric, electro-acoustic, baritone or bass guitars. It also works with many other acoustic and electric instruments including electronic keyboards, steel guitars, and instrument microphones such as harmonica and horn mics.

Mission Engineering

Demo by Antoine Michaud

Demo by Full Compass

Demo by Guitar Player Magazine

VM-Pro

Der Vemuram Jan Ray ist ein handgefertigter analoger Overdrive-Pedal mit dem Ziel, die punchigen, klaren Klänge der Fender Blackface-Verstärker der 1960er Jahre – oft als „Fender Magic 6“-Sound bezeichnet – nachzubilden. Er bietet natürlichen Overdrive mit großem Sustain und minimaler Kompression und erhält dabei den Charakter der Gitarre, während er die dynamische Ansprache verbessert. Das Pedal verfügt über einfache, intuitive Regler für Volume, Gain, Bass, Treble und einen Saturation-Trimmer sowie einen True-Bypass-Schalter zur unverfälschten Tonübertragung im Bypass-Modus. Handgefertigt in Japan mit hochwertigen Bauteilen und robuster Haptik ist der Jan Ray sowohl für transparente Verzerrung als auch für amp-ähnliche Zerre geeignet.

The Vemuram Jan Ray is a boutique analog overdrive pedal designed to reproduce the punchy, clear tones of 1960s Blackface Fender amps, often described as the “Fender Magic 6” sound. It delivers natural overdrive with great sustain and minimal compression, preserving the guitar’s character while enhancing dynamic response. The pedal features simple, intuitive controls including Volume, Gain, Bass, Treble and a Saturation trimmer, along with true bypass switching for unaltered tone when off. Handcrafted in Japan with high-quality components and a robust enclosure, the Jan Ray is suitable for both transparent drive and amp-like breakup tones.

Vemuram

Demo by  Ed "The Shred" Clarke

Demo by Michael Watts

Review by Mixdown Magazine

Review by Guitar Pedal X

Jan Ray

The Cali76 Compact Deluxe is an all-analogue recreation of the legendary Urei® 1176® studio compressor, with an unmistakable sound heard on countless classic albums. This studio-grade FET compressor uses Class-A, low-noise circuitry and a dedicated parallel compression control to bring your favourite recorded guitar tones to your pedalboard.

Origin Effects

Review by that guitar lover

Demo by Living Room GD

Demo by Sweetwater

Cali76 Compact Deluxe

Xotic

Xotic XW-1 Wah

Philippe Godde

A key component of many guitar sounds is a string of tasteful delay, which is just one of the things 2290 P provides. It is a time-based effect generator that - apart from delay - also offers chorus, flanger, tremolo, vibrato, phaser, panning, ducking and compression. 

And that is the essence of 2290 P: it is a faithful recreation of the original 2290, equally suited for adding delay to lead guitar tones and rhythmic patterns that can be used to build up powerful and inspirational walls of guitarscapes with or without additional modulation. In other words, 2290 P allows you to really dive in and carefully program it to meet all of your sonic ideas.

It simply evokes a distinct classic vibe from the past in a contemporary setting.

Review by guitar pedal X

Demo by Pedal Platform

2290p

DIEGO LEANZA

„Dieses authentische Reissue wird in unserer Fabrik in Bletchley gebaut und von Hand zusammengesetzt. Der Bluesbreaker wurde mit Präzision entworfen und für Qualität gefertigt und führt das Marshall-Erbe fort. Dieses Pedal ist bekannt für sein einfaches, aber wirkungsvolles Design und versucht, die samtigen und warmen Overdrive-Sounds des legendären Marshall Bluesbreaker-Verstärkers zu emulieren. Seit seiner Einführung im Jahr 1992 wurde dieses Pedal auf unzähligen Bühnen eingesetzt und hat sich zu einem begehrten Sammlerstück entwickelt, das von Enthusiasten heiß begehrt ist.“ - Marshall

"This authentic reissue is built and hand-assembled in our Bletchley factory. Designed with precision and crafted for quality, the Bluesbreaker carries on the Marshall legacy. Renowned for its straightforward yet impactful design, this pedal seeks to emulate the velvety and warm overdrive tones reminiscent of the iconic Marshall Bluesbreaker amplifier. Having been used on countless stages since its inception in 1992, this pedal has evolved into a coveted collector's item, highly sought after by enthusiasts." - Marshall

Marshall

Demo by Guitar Center

Review by mylespaul

Review by Hometone Blog

Bluesbreaker

Stefan Valenberghs

The Aqua-Puss Analog Delay MkIII delivers smooth vintage delay tones and tape-based echo with 20ms to 300ms of delay time.

Way Huge

Aqua-Puss MKII

PedalSafe Type WH3

QuickMount Type WH3

Pedal-Montageplatte für DUNLOP WAY HUGE SupaPuss Pedale

Pedal Mounting Plates for DUNLOP WAY HUGE SupaPuss pedals

Schutzabdeckung & RockBoard-Montageplatte für DUNLOP WAY HUGE SupaPuss Pedale

Protective Cover & RockBoard Mounting Plate For DUNLOP WAY HUGE SupaPuss pedals

Schutzabdeckung & universelle Montageplatte für DUNLOP WAY HUGE SupaPuss Pedale

 Protective Cover & Universal Mounting Plate For DUNLOP WAY HUGE SupaPuss pedals

David Litaba

Der legendäre STEREO CHORUS FLANGER war das erste Produkt von TC Electronic. Überhaupt! Unser Gründer, der auch Musiker ist, ärgerte sich in den 70er Jahren über die Qualität der verfügbaren Effektpedale - sie waren einfach zu laut. Also machte er sich als Ingenieur daran, ein Pedal zu entwickeln, das seinen Erwartungen und hohen Ansprüchen gerecht werden würde. So wurde 1976 das SCF geboren, und der Rest ist Geschichte, wie man so schön sagt. Aber hey! Niemand hat gesagt, dass die Geschichte zu Ende ist. Im Gegenteil, wir schreiben diese Geschichte weiter. Tatsächlich hat sich der Kreis geschlossen und wir treten in eine neue Ära der SCF-Geschichten ein. Darf ich vorstellen: SCF GOLD - ein legendäres Pedal! 

The legendary STEREO CHORUS FLANGER was the first TC Electronic product. Ever! Our founder, who is also a musician, was annoyed with the quality of effect pedals available back in the 70s – they were just so noisy. So, being an engineer, he set out to design a pedal that would live up to his expectations and high standards. That was how the SCF was born all the way back in 1976, and the rest is history as they say. But hey! No one said the story was over. On the contrary, we’re adding to that history. In fact, it has come full circle and we’re really entering a new era of the SCF tales. Please meet SCF GOLD – a legendary pedal to be! 

Review by reddit /guitarpedals

Review by Premier Guitar

Demo by Chords of Orion

SCF GOLD

QuickMount Type C

Pedalmontageplatte für große vertikale Pedale

Pedal Mounting Plate For Large Vertical Pedals

Stephen Killick

The DELUXE61 faithfully recreates the rich cleans, raunchy overdrive and dynamic, musical tremolo of the Fender® Brown Deluxe. Possibly the greatest amp of the early ‘60s. Featuring an all-analogue, valve amp-style signal path with an authentic bias tremolo circuit, the DELUXE61 brings a huge range of classic sounds to your pedalboard – with plenty of modern flexibility.

Demo by Pete Thorn 

Demo by JayLeonard J

Demo by Peach Guitars

Deluxe61

Jonas Kvinge

Often imitated but never duplicated, the elusive vintage "script" Phase 90 is at the top of the list for pedal collector's world-wide. The original version—available from the company's inception to the late '70s—practically defined the classic phase shifter sound, and was heard on everything from hard rock, jazz-fusion, to funk hits. The MXR Custom Shop Script Phase 90 brings back the headroom and clarity of the original, along with its ultra warm and smooth phasing and reduced midrange swell. And it comes dressed in the original smooth orange paint job and script logo with an LED and AC power jack, direct from the MXR Custom Shop.

Review by reddit.com/r/guitarpedals

Review by Ultimate Guitar

Demo by Octoplod

Script Phase 90 CSP101SL

Erfahre mehr über das Surfybear Metal Reverb reverb-Pedal von Surfy Industries auf PedalPedia – der umfassendsten Online-Ressource für Effektpedale ▶️ Offizielle Spezifikationen, Handbücher, Produktvideos und mehr